Having problems with your Fantom Vacums Lighting Canister Vacuum ?

How do i get the wheels off my fantom lightning vacuum cleaner LC63K

\015 Need to take apart and the wheels are holding it together\015

Answers :

Repair Help & Product Troubleshooting for Fantom Vacums Lighting Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i get the wheels off my fantom lightning vacuum cleaner LC63K

... Fantom Vacums Lighting Canister Vacuum

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01

... Vacuums

I own a Halo vacuum cleaner and I cannot get the wheel to turn, the belt is on securely but it still will not turn, what am I doing wrong?

... Halo Vacuums

My DC-25 will not return to the upright position. I emailed Dyson support and the response was: "The DC25 stabilizer wheels will not lock into position if the “spokes” on the red pedal are not seated correctly." I agree with that assessment, but cannot figure out how to get the spokes on the red pedal to seat correctly. The manual is useless for this problem since that part of the vacuum cleaner came already assembled, so the manual does not address it. Help.

It sounds like the undercarriage unit has failed. It is a common problem on ball models. The DC25 is a recent model so would still be under Dyson's 5 year guarantee. Get them out to it. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Eurolab xr210 robotic vacuum cleaner right wheel motor seized. Repair or replace? And where can I get spare part? Thank you.

... Vacuums

I was give a Fantom Thunder Vacuum cleaner from a friend it has lost suction and is whistling how to a get it working right?

You may have a plugged filter. If it has a rotating bar at the floor it may be plugged with hair etc.. ... Vacuums

How to attach the wheel on a Kenmore Premalite Vacuum Cleaner?

... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]

Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

My bissell 3595-2 vacuum cleaner started turning off the power automatically. Now I can not get it to turn on. This vacuum cleaner is still in real good condition, as I have hardly used it. Please advise what could be wrong. I was thinking maybe a loose connection with the on-off switc.

... Bissell Vacuums

Fantom FM741B vacuum cleaner user manual - Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

How to replace vacuum cleaner belt on Fantom 310K upright

... Fantom Vacums Vacuums

Fantom Lightning canister vacuum manual needed. Fantom Vacuum closed in 2002 and I need help finding a free manual for model number: BPSRLC51

... Fantom Vacums Lighting Canister Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430

Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

Where can I get a switch for fantom vacuum - Fantom Vacums Lighting Canister Vacuum

... Fantom Vacums Lighting Canister Vacuum

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.

... Kenmore Progressive Direct Drive 30912 Vacuum

Hot cord the cord on my vacuum cleaner has been getting very hot the heat is from one end to the other incuding the plug and also where the cord exits the back of the canister please help I love this vacuum cleaner it has been faithful to me for over 15 years!

Likely after all these years that the motor is starting to go bad and draw more amps thasn it should. a new motor at a vac dealer is your best bet. it was likely made by panasonic, so a new panasonic is your best bet, and less $$$than the kenmore for ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Electrolux 5500 The cord on my vacuum cleaner won't retrack. What is the trick to get the back end off the vacuum cleaner? It looks like it was pulled out too far.

Depends on which model you have, but most of them you take off the center section, then you cab get to the 2 screws on top , and there is a screw on the bottom, then the back end will pull off. But I wouldn't try taking the cord reel apart, if that ... Electrolux Lux 5500 Canister Vacuum

Fantom Cyclone XT Vacuum Cleaner


Replace wheel on Kenmore vacuum cleaner

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.

I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat

It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

I have a multifunction robotic auto vacuum cleaner model number XR210. It doesn't seem to be charging when at the docking station. The light is flashing on the docking station as if it was charging, but then I am getting intermittent noises like the vacuum is about to start up, then it beeps and goes silent again. I have emptied the machine. The display does not read 88 as if there is a malfunction, so I'm really not sure what's wrong with it. If I put the vacuum to the docking station the displ

... Vacuums

I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?

That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel

What is the exact model # please?Thanks!! ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1252 seconds