Having problems with your Fantom Vacums Lighting Canister Vacuum ?

Fantom Lighting Hair and Dirt is going right through.

\015 Hair and dirt is going right through to the filters and making a real mess in the back of the vacuum.\015

Answers :

Repair Help & Product Troubleshooting for Fantom Vacums Lighting Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Fantom Lighting Hair and Dirt is going right through.

... Fantom Vacums Lighting Canister Vacuum

Dirt finder I have a Hoover U6439-900.  After the cleaner was used a few times, the dirt finder light cycles between green and red on the regular setting and will not go to green.  On the sensitive setting, the red light stays on most of the time.  I have tried to run the cleaner to remove any dirt but have not solved the problem.

The sensor may be bad, or it may be coated over with dirt. Re,ove the hose at the back of the vacuum, the head of the sensor is down inside that opening, reach in there and clean it off and see it that corrects the problem, if not replace the sensor ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Savvy The red light for the dirt finder is on when pushing forward and the green light is on when pulling it back. This happens all the time. It's like the dirt finder sensor isn't working right. It seems to be picking up good and we keep the filter clean.

Does this happen at both Dirt Finder Sensitivity settings? ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Vaccuum issue I just bought a Eureka upright model 5892 BVZ, my concern is, I bought it on sale (floor model) and it didn't have a manual with it. I took it home and tried it, and although it appears to be working very well there is not dirt in the catch bin on the front of the unit. I tried the hose w/attachment and again it worked very well in picking up the cat hair, but where does the hair and the dirt go, I am afraid it is spitting it back out somewhere since I can not see anything in the c

If the dirt being vacuumed is not going into the dirt cup, then it must be just stuck in the hose and evenually will clog up. Check the hose and see it there is a clog in it, otherwise you have a years warranty on a new vacuum, take it into a warran ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen

Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o

... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.

... LG Vacuums

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

The Dirt Sensor lights will not go out. It doesn't matter if I am vacuuming carpet or tile floor, the dirt sensors are all lite up. I can't locate my owners manual.

Your machine could be clogged, check the tools for suction. If its a bag less model you might need to clean or replace your filters. ... Kenmore Vacuums


You need to replace the belt whenever the green brush indicator light goes out or is not steady. Be sure to observe the wear settings when re-installing the brush. The ends of the brush are marked with 1, 2, or 3 notches and numbers. In normal use th ... Kirby Ultimate G Bagged Upright Vacuum

Hi, I have a cleanview bagless model# 3576-2 and my belt keeps breaking (it seems like one of the rings it should wrap around is missing) right now I have been wrapping it around the brush and a metal rod. Also, the dirt collected is going directly into the hose and not the bagless filter. What is going on?

... Bissell 3576 CleanView II Bagless Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Dirt and hairs not going into cylinder

It's not the filter that's the problem.  Air should go first to the cyclones, then to the filter, so the filter catches only those finest dust particles that are not trapped in the cyclones.  The most likely cause of the problem is that the ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

Dirt not going in to the right "chamber"

Hello. i can help you. here is your link to a free replacement manual\015\012\015\012http://www.eureka.com/owners_guide.jsp\015\012\015\012 ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Fantom Canister The vacuum head light keeps going on and off as well as the suction.  I actually purchased a new head, at the recommendation of their service dept., and the problem is still happening w/the new head.  Any suggestions.

It sounds like you have a hose problem. You should be aware that the Fantom company went bankrupt many years ago. I know that the Fantom name was bought by another company and there may be Chinese units sold under that name, but service and parts ava ... Fantom Vacums Lighting Canister Vacuum

I have a Kenmore 116.36932 (upright bagless vacuum) The dirt sensor lights won't go green. I have changed the filter, and check for clogs.

... Vacuums

We have a kenmore canister vacuum, the part that is attached to the wand that picks up the dirt doesn't work, when it's on the carpet the light does not go on. Do we need to buy a new vacuum or is there a replacement for this part.

Hard to say without the correct model number.\015\012\015\012However, you could check these things first:\015\012\015\0121- Is the belt that runs the brushes on the end pieces broken? If it is, is needs to be replaced.\015\0122- Is there ... Kenmore Vacuums

Vaporetto 1300 - No steam coming from hose - red pressure light (Right hand switch) not going out. ??

... Polti VT1300 Vacuum

The lights which tell you if you are going at the right speed on my Bissell PROHeat Pro-Tech have stopped working. Just wondering if this could be as simple as a bulb or more serious. Also, how do you remove the clear panel at the front for cleaning? Thanks

The clear view window is unscrewed with a philips screw driver on either side of the nosel opening (top) but make certain the handle is layed back so as to alleviate twisting off the clear view cover. There are six (6) screws that hold the top cove ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Dirt Devil Quick Power hand vac model 0896 won't charge. Red light doesn't go on when plugged into wall. We've lost our manual, need help troubleshooting.

... Dirt Devil M0896 Quick Power Bagless Handheld Vacuum

I love my hoover F5912-900 scrubber however it has stopped sucking up the water. Is there a place that it could be blocked with dog hair or other dirt?It blows out air, but does not **** up the dirty water. How would I go about unclogging it?

Hi Shirley. Im afraid I do not have a solution for you rather I have the same problem.exactly it only blows..My machine is brand new I was using it for the 2nd time only......i also cannot find anywhere to unclog this thing....I even took the front p ... Hoover F5912-900 Upright Steam Vacuum

My irobot Dirt Dog won't go into a cleaning cycle. It is charged, but when i hit the clean button it does nothing. new battery installed a week ago. the LED lights under the "clean" button are flashing in sequence, "Green, Green+Red, Green". Then the sequence immediately stars over. Can someone help me?

Hi, A very common problem with the I robot is the wheels on the underside become clogged with dust and dirt. Turn the device over, and remove the bottom cover that is covering the wheels. At this time, remove the dirt and blockage from the wheels, an ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

My roomba backs away from docking station then starts to go then stops and spin left then stops and spins right after a few times stops and beeps many beeps. What is the problem

It sounds like the 9-beep error. You can fix it by buying a repair kit from www.eesolutions.ca. I fixed mine in about an hour and a half. ... iRobot Roomba 530 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0442 seconds