Having problems with your Fantom Vacums XT450K Upright Vacuum ?

Beater bar won't turn - Fantom Vacums XT450K Upright Vacuum


Answers :

Could be 1 of 2 things. first try to spin the bar with your finger. "MAKE SURE VACUUM IS NOT PLUGED" "NO POWER TO UNIT" If it does not move, it might be the barrings if not it might just a simple belt replacement. good luck.
Repair Help & Product Troubleshooting for Fantom Vacums XT450K Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater bar won't turn - Fantom Vacums XT450K Upright Vacuum


Could be 1 of 2 things. first try to spin the bar with your finger. "MAKE SURE VACUUM IS NOT PLUGED" "NO POWER TO UNIT" If it does not move, it might be the barrings if not it might just a simple belt replacement. good luck. ... Fantom Vacums XT450K Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Beater bar on upright Kenmore Intuition vacuum will not turn.


... Kenmore Vacuums

Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took


... Vacuums

My Hoover Platinum LiNX Cordless Stick Vacuum beater bar is not turning. After removing some clogged hair and items...the vacuum cleaner has suction, but the beater bar will not turn. What to do? The belt is still attached and will turn manually.


... Hoover Platinum LiNX Cordless Stick Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet


Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

Beater bar not turning - Cirrus CR99 Bagged Upright Vacuum


The number one cause of the "beater bar" (or brush roller) not rotating is a broken belt. \015\012The number two cause of brushes not rotating is that something is jammed & wound around the roller, preventing it from rotating. ... Cirrus CR99 Bagged Upright Vacuum

Dyson dc25 beater bar wont turn - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The beater bar won't turn - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Replace the belt - it is broken or has a flat spot on it. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I cannot get my beater bar to turn - Kirby G4 Bagged Upright Vacuum


Manual on how to attach the nozzle - HERE. Or you may watch the video on the bottom of the home page on goodvac.comGood luck,Rocky ... Kirby G4 Bagged Upright Vacuum

Beater bar will not turn - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The beater bar will not turn - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hello rebh. Generally when the vacuum beater bar will not turn it is because the belt that turns this beater bar has broken. \012\012That said, most of the dyson's require you to buy a beater bar assembly which includes the belt. Any ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The beater bar will not turn - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson.Make sure that the brush control dial on the cleaner head is in the correct position for use on carpets. It should be in the centre position when in the upright mode and then when the head is released into the clea ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson blueprint beater bar won't turn - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


The Dyson DC 17 has a rug / floor switch on the head of the vacuum. Please check to make sure the switch is in the Rug position. If the brush roller still does not turn then you have broken the belt and need the following part.\015\012 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar not turning, making loud sound - Dyson DC07 Bagless Upright Cyclonic Vacuum


This machine has a clutch assy. that slips and makes a loud noise\015\012when something gets stuck in the roller brush. If you have nothing stuck in the roller brush chances are the clutch is worn and needs\015\012replacing. Not an easy ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater brush runs intermittently - Fantom Vacums Cyclone XT Upright Vacuum


Try changing the the belt.If it is worn it could cause your problem ... Fantom Vacums Cyclone XT Upright Vacuum

Beater bar will not turn - Dyson DC25 All Floors Bagless Upright Vacuum


Something probably got caught in the beater bar whilst you were vacuuming, that'll cause it to stop itself so that it doesn't cause any further damage, solution:\015\012- make sure the beater bar is clear of obstructions\015\012- step on ... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson vacum beater bar does not work - Dyson DC14 Bagless Upright Cyclonic Vacuum


DC14 have two drive ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?


Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

My dyson beater bar quit turning - Dyson Ball DC24 Bagless Upright Vacuum


... Dyson Ball DC24 Bagless Upright Vacuum

Beater bar on Dyson upright won't turn when handle is lowered


I have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires connect to circuit board lead to the beater bar. The wires broke where they go through the black rubber gommet. You need a torx ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1287 seconds