Having problems with your Fein 9-55-13 Turbo II Bagged Canister Vacuum ?

Cracked lid/top of fein vac model 9-55-13

\015 The lid to which the handle is attached is badly cracked. Can this part be replaced? I can not find anything as far as a parts listing online for fein to reference. Can you help me out? Thanks\015

Answers :

Contact Rudi at E & H Repair in Chicago. They are an Authorized Warranty Repair Center for Fein. The phone no. is 312-829-6770. Email is [email protected] Good luck
I used West System 105 resin with hardner and high density filler. Mixed it up and spread it around the break. Works fine and that was a couple of years ago. However, my Fein vac has started howling so much that it can be heard a block away. Figured it had a bad bearing. Opened it up and finally got the motor out but for the life of me I can not figure out how to gain access to the bearings. Must have them but I can not get to them. Anyone else had this problem.
Repair Help & Product Troubleshooting for Fein 9-55-13 Turbo II Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cracked lid/top of fein vac model 9-55-13


Contact Rudi at E & H Repair in Chicago. They are an Authorized Warranty Repair Center for Fein. The phone no. is 312-829-6770. Email is [email protected] Good luck ... Fein 9-55-13 Turbo II Bagged Canister Vacuum

The fan on my Dirt Devil model 103 hand held vac cracked. I bought what was designated as the correct replacement fan but the hole in the center of the fan is a lot smaller than the shaft that it has


... Vacuums

Parts list for model: EP754 The plastic  hose connecter from hose to vac cracked i need new connector


Shark vacuums generally are not repairable - in this case, Shark doesn't sell just the part; ya gotta buy the entire power head. And it costs more than the vacuum did new.\015\012\015\012Shark's are considered throw-aways; when they break ... Euro-Pro S3325 Handheld Steam Vacuum

Motor died I own a fein vac that is perhaps five years old. It appears that the motor is toast. Is it possible to order a replacement and install it myself? My model # is 9.11.20 Thanks for reading, Kevin


Yes you can its very easy you will have to get the model number the serial number and that will help you find one online try sites like vac motors or anything related, i have worked on industrial vacs mostly so my connections will not help you but yo ... Vacuums

I have a model 1561 electrolux central vac..can i use a hose and accessories from a model 15448 model electrolux central vac to compliment my central vac unit


If the hose fits into the inlets, then there should be no problem. ... Electrolux Centralux Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I have a craftman shop vac model 500A , 5GAL.,1.25hp. why does Sears say that's not the model num. IT'S THE ONLY MODEL NUM. ON IT!!! IF IT'S AN OLD MODEL,WHY DONT THEY SAY IT IS THE SAME AS MODEL#***** AND WHY DOESEN'T THE FILTER,BAG'S ect.SAY, WILL ALSO FIT MODEL 500A


... Craftsman 17765 Canister Wet/Dry Vacuum

Need a manual for the shop vac model # 2E200 - Shop Vac Shop-Vac& Mini Hang Up Wet/Dry Vac Vacuum


... Shop Vac Shop-Vac& Mini Hang Up Wet/Dry Vac Vacuum

Switch for Shop-Vac model QPL650 - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

Shop vac model 3331.5 H owner manual - Shop Vac 333-32-08 Blower Vac Wet/Dry Vacuum


... Shop Vac 333-32-08 Blower Vac Wet/Dry Vacuum

I have a kenmore upright model 116.36933 vac. motor wont stop unless i pull th plug the buttons work on everything else but stopping the vac


... Vacuums

Shop-vac model 90L550A motor wont run


Yes replacing the link would work, but that would not fix the cause. You have either pulled the wiring to the point of pulling apart the connection or there is a short. Which would be in the way of a grounding effect causing the link to heat and melt ... Vacuums

HOOVER VACUUMS MY MOTHER'S WORK, MERRY MAIDS, USES ALL HOOVER VACS. THEY ARE LIGHTWEIGHT-UPRIGHT-BAGGED VACS. I TRY TO FIX THEM WHEN THE MAIDS BREAK THEM; BUT, I'M HAVING PROBLEMS WITH A BURNING SMELL AND ONE MOTOR EVEN SMOKES. I'M NOT SURE THE MODEL. CAN YOU HELP? THANK YOU.....


Go to thehooverstore - this site lists a whole bunch of hoover machines, exploded diagrams and parts lists. ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

We have an Eureka The Boss Central Vac Model ACV2001B. When you plug in the vac the motor starts momentarily and then stops. What could be the problem? Thank you.


Most likely there is a short in the low voltage wiring in the hose. ... Vacuums

Need manual for Ridgid model 9500 Vac/ - Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum


Please be more specific with the model make of the vaccum.\015\012\015\012Regards\015\012\015\012\015\012Anand ... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie


The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The vac just goes red hot and switchs itself off no idea why. alyx pets 2000w is the model of the vac.


Its activated its thermal cut off. Check the filters - if the paper pleated cone filter is blocked throughly tap it gently to loosen dirt before washing it completely and drying it in a low temp tumble dryer (put it in a pillow case with a towel insi ... Vacuums

How does the upholstery cleaning hose attach to the vac? Hoover Steam Vac Deluxe Model # F5860-900 Series 17.9


See if this manual helps:\015\012http://www.hoover.com/pdfs/manuals/F5857955.pdf ... Hoover Steamvac F5860-900 Vacuum

NEED A 24V BATTERY AND A CHARGER FOR A 2/HALF GALLON VAC MODEL#RC92S24V. THE BATTERY IS MODEL#RC24v


Check Amazon. ... Shop Vac Vacuums

IS A CRAFTMAN SHOP VAC MODEL 500A THE SAME AS THE 17765 MODEL?


... Craftsman 17765 Canister Wet/Dry Vacuum

Replacement motor for Shop vac 12 gallon 5 HP contractor series wet/Dry vac model number LM500.


... Shop Vac Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1451 seconds