Having problems with your Fein Multimaster Rs - Msxe 636 - 2 Rs ?

I have a fein msxe636 multimaster the capacitor has burn out i have a replacement but not sure how to fit

\015 There are 3 leads the longest has a long metal connector not sure where it goes\015

Answers :

It needs to be put up between plastic housing and field/stator.
Repair Help & Product Troubleshooting for Fein Multimaster Rs - Msxe 636 - 2 Rs

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a fein msxe636 multimaster the capacitor has burn out i have a replacement but not sure how to fit

It needs to be put up between plastic housing and field/stator. ... Fein Multimaster Rs - Msxe 636 - 2 Rs

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus

... Bissell 6595 Lift Off Bagless Upright Vacuum

Every time I replace the two belts on my panasonic mce3002 they burn rubber and the small belt burns out am i fitting them incorrectly

... Panasonic Vacuums

We replaced the belt after about 5 uses, and now every once in a while it smells like burning rubber, I checked to belt to make sure it was ok, and then last week it started smoking. Is there reported problems with this model?

If the belt is hot or burning during use, it could be due to a beater brush, which the belt drives, being bound up in some manner.\015\012The beater brush is removed during belt changes and should be cleaned of all debris as best you can.\015\012At e ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Pool universal wall fitting for pool needs to be replaced

... Vacuums

Burning smell from motor...what needs replaced?

Without the complete model number, I don't know for sure what componets you have, most likely is the motor. You will have to take the motor cover off and check it out. You can go to sears.com, click on parts, enter your complete model number, scrol ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Can the suction hose fitting where it attatches to the base be reattatched, it has torn away from the snap-on fitting or do I have to replace the complete hose unit, the model is F5878-900.The existing hose is screwed into this fitting and glued.

You must replace the whole hose unit. its not very cheap either ... Hoover F5878-900 SteamVac Upright Vacuum

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest

I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total

... Vacuums

Im looking to replace the motor mines when bad looking to replace the burn out motor

... Hoover F5906-900 Upright Steam Vacuum

Nilfisk GM 90 motor bearing Hi I have replaced the motor bearing on the GM 90 model but having problem with re fitting the turbyne I forgot the sequence it has 2 turbines and 4 2 inch washers Can you please tell me the sequence it is fitted Thanks,,,Ps the motor is 100% ok now Peter

... Nilfisk Vacuums

No action Hi: My brush roll won't budge. After we cleaned out all the hoses and replaced a badly worn belt (burned?) when I turn it on the smell of burning rubber and smoke has continued. What hurts is that I don't think I've used the vacuum a total of 10 times ... and I had such high hopes. Ideas?

I had the same problem with the belt breaking and the roller not spinning. I read about giving the roller a couple of revolutions to seat the belt, so I put another new belt on. It still didn't spin. I realized it was the end cap that was not spinnin ... Eureka 2961AVZ Bagless Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Burning smell There is a burning smell when I run my Kirby Ultimate G.  The smell seems to be coming from the belt.  I looked at the brushes and they are spinning so the belt is working.  the Post on the vacuum is getting very hot not sure if that is normal.  What is causing this?

Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum

Replace belt on eureka big boss sweeper. Bought sweeper got it cheap and it needs a belt. So i don't have anything to go on to replace it. Seems like there is a pulley below and not sure how to install

... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

The top of my 500ml/0.6qt thermal vacuum flask is broken and i'm not sure if i can get a replacement as the thermos is still okay. i would be grateful to know if i can get a replacement top so i don't have to buy a new one. Thanks meryl hawkins

Hi there,\012Well yes you can purchase a separate flask for your thermal vacuum, you may purchase them from the dealer or you can please post the brand of your thermos so we can help you to find the part.Good Luck!! ... Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Does the hoover runabout u427-930 have a filter? I replaced the belt and next to the light bulb was a square gray mat that looked like a filter covering a screen full of holes that looked like the motor was behind. I think it was a mat of cat hair so I took it off and threw it away; I just want to make sure that it wasn't a filter that I need to replace.

From doing a search on the internet and hoovers website it looks as if this unit does not have a filter. Such as a hepa that needs to be replaced or that is washable. So i think you are safe and dont need to worry about it. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!

Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.

It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

Is it easy to replace the debris door myself on the vacuum? Mine broke and I want to replace it myself but not sure if its easy or not.

Take a close look at the old debris door and determine whether or not you have the tools necessary to do the job. If you do, remove the old one. The new one will go one in exactly the opposite steps. ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.

On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0602 seconds