Having problems with your Fein Multimaster Rs - Msxe 636 - 2 Rs ?

Where does the long lead go on my multimaster capacitor go

Answers :

Close to the bottom in the corner near the motor stator (= electric field) between the machine housing and the stator there is a narrow metal strip connection point visible which makes contact with the metal outer surface of the stator, the strip sits against the corner on the underside between the motor stator and the machine housing from the front so pushed to the back comes out so at the contact side of all sliding contacts you will see are that part, I myself always recommend letting eight jure the capacitor because it only makes sense for radio interference suppression only at work places.
Repair Help & Product Troubleshooting for Fein Multimaster Rs - Msxe 636 - 2 Rs

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where does the long lead go on my multimaster capacitor go

Close to the bottom in the corner near the motor stator (= electric field) between the machine housing and the stator there is a narrow metal strip connection point visible which makes contact with the metal outer surface of the stator, the strip si ... Fein Multimaster Rs - Msxe 636 - 2 Rs

I have a fein msxe636 multimaster the capacitor has burn out i have a replacement but not sure how to fit

It needs to be put up between plastic housing and field/stator. ... Fein Multimaster Rs - Msxe 636 - 2 Rs

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like

I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

Fein Multimaster makes more noise. I have used it a lot and, it sound like a bearing going bad. Any ideas?

... Fein Multimaster Rs - Msxe 636 - 2 Rs

Cannister model#11627915701. connector terminals in extensionwand ,and wlre harness in hose handle get hot,,,look a bit singed.. can order and do ourselves. but would like a "tune up " ,cleaning of vacuum as well. purchased in 2008. have long haired dog,,,can't afford to be without it for very long. have sears store in clay ,ny. lady I spoke w/ says it would get sent out and take at least 2 weeks.!

... Kenmore Vacuums

Vacume did not come with screws to hold handle to Vacume need the screws handle falls off vacume hits the floor [email protected] Model # 3041 Type - B2 The answer is simple, send the screws please this will fix the problem. Thanks Dr.Tracy Massie Dr.Tracy Massie Harvard;Dr/PHD; Chief Officer of Internal Medicine;Lead Surgeon Dr. Child Disorders; Princeton Dr. / PhD.; Chief Medical Officer; Lead Councilor

... Eureka 3041BZ Upright Vacuum

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

My Oreck 2600HH won't turn on. The wiring seems right, but when I check the black lead and white lead at the motor there was no voltage when I turned the switch on

... Oreck XL2600 Vacuum

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!

... Oreck Vacuums

I have a new Toyota RS2000 that I was bought as a gift. I received it without a manual which I have now obtained, but now I have gone to use it the power lead does not seem to fit into the machine. Is it possible I was supplied the wrong lead or am I doing something wrong?

It is quite possible that you were supplied the wrong lead, seeing that the manual was missing, the contents of the package might well have been tampered with. Contact the person who gave you the machine and ask them to either check wit ... Vacuums

I have an electrolux central vacuum in my house. My central vac hose has something stuck in it, I think, maybe a sock. I tried to put a long dryer wand down it but the hose is just too long. Does this need a repair man or new hose?? Any idea of a way to blow it out? Thanks.

The best way to clear an obstruction is to blow it out by attaching the wall end to the exhaust of a shop vacuum, or using an air compressor.\015\012You can try holding the wand end of the hose directly to the CV in port and turning the machine ... Electrolux Central Vacuum

The lead on our machine is becoming frayed - is it possible to replace the lead and if so, how is it achieved? John Tuffley

If you are refering to the Electrical Power Cord? Yes, this can be easily replaced or repaired. \015\012Depending upon where the cord is damaged, you can either cut it a little shorter and install a replacement electrical plug end (available ... Sebo Automatic X1 Bagged Upright Vacuum

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you

Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?

Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

Hoover wiring the blue wire that is in the lead that runs from the hoover to the plug that goes in the wall has come loose at the hoover end and has come out of the actual hoover. i've unscrewed it but am unsure as to where the blue lead (bare copper) needs to be screwed... if you see what i mean?!!

Hello lukeplayer,\015\012Based on your description, ( first disconnect the plug from the wall recptacle).You will need to open up the Hoover Vacuum Body to gaion access to the internal wiring. In order to better assist you, please provide me wi ... Hoover Vacuums

How long does it take to recharge the battery? How do I know when it is recharged?  This is on a Shark Cordless Sweeper #V1950.  I have searched the manual and it tells how long to charge it before you use it the first time, but not on subsequent charges.

... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Long spring S3101W Took apart have a long coil spring where does it go

Hi,The spring goes on the hose to give the plastic tubing some support...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a

You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

It seems like the hose might be clogged. How do I get possible blockage out? The hose is so long - too long for a wire hanger to reach all the way through.

Put a golf ball through it or if that is to big get a smaller heavy ball bearing put in hose and hold hose up until it passes thru ... Miele S246i Bagged Canister Vacuum

GE on/off timer for a bathroom fan - switch has four wires Green - ground White - neutral Black - power Blue - lead My fan has two - white neutral and black lead I have tried every configuration and cannot get the fan to work. Any suggestions?

I would guess that the black wire on the timer is the power in and blue is the power out to the fan (hook it to the black wire going to the fan) The other colors are right. ... Vacuums

We have Nilfisk Tempest 1500W bagged cleaner. It just stopped working and I have taken off top cover and all wires/contacts look OK. But power still not getting through I assume. The retractable lead goes into base and cant get to this area. How do I check main lead or perhaps you provide details of serviceman. On North Shore, Auckland, NZ.

... Vacuums

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.

... Electrolux Vacuums

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it

It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

Hello, I,ve just bought an Italian designed 3 bulb 70's wall lamp. It has a 2 wire lead feeding out with 2 wire lead running from one bulb socket To the other 2 inside the casing. I'm trying to wire it in my porch which has 3 wire cable coming from a 13amp plug for power. Any suggestions on making this work please ?

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0266 seconds