Having problems with your Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum ?

How do you wire a 2 speed fq motor. I know the blue/blue. the red/red. The yellow /yellow and I believe the whites together with the grey of the pn outlet. Does the black from the motor the black from the cord and the other grey from the pn outlet connect together ?

Answers :

I have not seen the new two speed but sounds like the wiring is coded to teh switch by colorOn a single speed it would be this way.
\015\012Power cord to side 1 of switch.
\015\012Switch to motor 1 and PN receptacle 1, etc
\015\012Then cord to remaining motor 2 and PN 2 so by color should be accurate.
\015\012Note PN receptacle should likely be powered at both speeds....it is on other vacs
Repair Help & Product Troubleshooting for Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you wire a 2 speed fq motor. I know the blue/blue. the red/red. The yellow /yellow and I believe the whites together with the grey of the pn outlet. Does the black from the motor the black from the cord and the other grey from the pn outlet connect together ?

I have not seen the new two speed but sounds like the wiring is coded to teh switch by colorOn a single speed it would be this way.\015\012\015\012Power cord to side 1 of switch.\015\012Switch to motor 1 and PN receptacle 1, etc ... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks

... Bissell 3750 Lift Off Bagless Upright Vacuum

Rainbow mod. D4C have new on /off switch, 2 black, 2 blue wires. need to connect power cord, motor and carpet sweeper?

Are the wires still attached to the old switch? If they are, hook them up to the new switch in the same, physical way. If they aren't attached, you might take it into a vacuum repair shop- they could probably help you figure it out, if you bought ... Rainbow Technologies D4 Bagless Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.

... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t

... Vacuums

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce

I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the

Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.

... Miele S251 Flamenco II Bagged Canister Vacuum

Where do you hook the clear hose that is in the compartment with the motor ? Second where the vacuum hose connects to the bag it keeps cutting in and out of power. I replaced the female cord to motor and still cuts out."no suction "

Would you care to tell us the make and model of the vacuum you're asking about? ... Vacuums

I replaced the motor on shopvac model 92L625A and a little black plastic piece fell out between the switch on top and the actual rocker switch. I would like to know how toput it back together properly because it keeps falling out. Can you help or send a schematic?

... Shop Vac Vacuums

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!

... Dyson DC05 Bagless Canister Cyclonic Vacuum

I have a Filter Queen model CA-96 Majestic Triple Crown, crome & black canister vacuum. The brush in the motor wand isn't turning. We have checked the connections and anything else we can think of. I don't have a manual. What can we do to fix it?

... Vacuums

While vaccuming it just stopped. Tried another outlet and checked power cord. Did find tube clogged with a dirt clog but no motor strain heard. Cleaned it out, Still not running

On the back of most vac's , u will find a red butten,use that to reset the vac. but even if that works u can avoid this usely buy ajusying the vac to a higher set . that helps reduse strian that the belt gets.\015\012 thanks\015\012 ... Bissell 68001 Canister Vacuum

Reinstalling a hampton bay ceiling fan model-HL52QV P 3LC14 and I do not recall how to wire it to the house electric. A black wire and a blue wire are tied together and a white wire are present fromthe fan. Whichone is connected tothe hot wire in my fan electric box inthe ceiling.

The black and blue wire should conncect to the black wire in the electric box and the white wire should connect to the white wire in the box. This assumes the wiring was correctly installed.Jim ... Vacuums

I need wiring diagram to connect power cord, motor, and switch on a shop vac

... Shop Vac 84M200 Wet/Dry Vacuum

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?

Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

I just purchased a black and decker corded hand vac/blower/inflator. I plugged it in (for the first time ever) it started and then shut off immediately. I tried different outlets thinking it blew a circuit in the first one. However it still won't start. Very frustrating!

Unfortunately those units are prone to breakage they are also usually a sealed unit (not able to take apart). The best thing to do would be take it back where you bought it and try to get your money back. They just aren't worth fixing. V ... Black & Decker Vacuums

How do I remove the collar to replace the cord to the power bar, I have the part, cannot get the little collar off to connect the new wire, purple to white and white to black... cannot get the old wir

... Hoover Powermax S3530 Bagged Canister Vacuum

Rplacement part I need the part # or a schematic so I can determine the part # for the little black cylinder with 4 wires sticking out of it that commects the power cord to the two motors.

Http://www.oreck.com/customer-service/owners-guides.cfm#Her is the oreck manuals web page.They can also tell you where to get parts. ... Oreck XLS700A Upright Vacuum

My Electrolux Epic 6500 will not turn on. I have no indicator lights other than power cord is connected. Prior to the vacuum not working the motor seemed to be going slower and slower till it stopped completely.What could my problem be and how would I then test to confirm?

... Electrolux Epic 6500 Vacuum

Meile Solaris. Power cord connection faulty. Unit powers on/off when cord is being retracted/pulled out. Maybe a break in wire close to connection point in vacuum. Or, the connection point itself is loose? The problem likely resulted from trying to use vacuum at furthest extent of cord.

Cord reel likely needs to be tightened. requirs disassembly and large washers installed to keep reel connections tight. Jim ... Vacuums

Connecting motor part

Hi Charlotte, \015\012Yes, colour coding of wires is a nightmare, isn't it!?\015\012Red and brown both signify "live", and blue and black both signify "neutral".  So you should connect brown to red, and black to blue.\015\012I hope this is ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?

... Oreck XL21 Bagged Upright Vacuum

I Have a kenmore 116.23612300 canister vacuum which will not start. I have power everywhere but nothing going to the black wire to the motor. Seems to stop at the pcb asm, #KC86WBZRZ000 . Nothing from there to the black motor wire. White wire to motor has continuity everywhere it should. Ruled out just about everything but the PC board. What does it do exactly?

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0481 seconds