Having problems with your Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum ?

Vacuum not coming on, was working fine the last time I used it

Answers :

Repair Help & Product Troubleshooting for Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing

No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Vacuum not coming on, was working fine the last time I used it

... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

Hi, I have a Hoover windtunnel t series vacuum. It was working fine until the last couple of times I used it. It just does **** uo the dirt. It **** a little, but not as strong as it used to be. Already checked for clogs (didn't find) and cleaned it and still doesn't work. Any ideas? Thanks!

This model, along with some similar ones, has been recalled. Stop using immediately. See the following site for information.\015\012\015\012 ... Hoover UH70205 WindTunnel TSeries Rewind Plus Bagless Upright Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi, I have a older electrolux canister vacuum that doesn't work. I have power but no succion at all. It worked fine last time I used it...what's wrong with it?

You may have a colg in your hose, try blowing it out.\015\012\015\012Bob\015\012http://evacuumstore.com/ ... Electrolux Lux 5500 Canister Vacuum

My oreck xl 3800 H2 upright vacuum cleaner does not turn on. It worked fine the last time I used it. Is there some sort of fuse that may have burned out?

Usually no fuse on these.\015\012\015\012Assume the outlet has been checked?\015\012\015\012I'd look at the on/off switch (that is a 2 speed unit, tight?) or the diode the gives the 2-speed choice, or the power cord as my firs ... Oreck Vacuums

My Fantom Lightning canister vacuum won't turn on at all, worked fine last time I used it.

You need to turn over and remove the case to get to the motor.When you get to the motor you will see a white wire going to the motor from the switch,it has a white cover over the wire,pull this cover back and there is a small fuse that is probably bl ... Fantom Vacums Lighting Canister Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

I have a miele S4210 vacuum. It has a SAB100 accu nova battery brush which will not work. After charging the battery, light comes on saying not charged and now the power head brush won't turn. I had problems with my first powerhead so I purchased another and it worked for a short time and now I have the same problem again. I have four batteries I use interchangeably but nothing seems to work. I spent a fortune on this vacuum and to tell you the truth I hate it! Contacted Miele after 1st year of

... Miele S300 Bagged Canister Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage

If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.

This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u

Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug

... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

I have an electrolux oxygen canister that's 4 yrs old and it just stop working. It just doesn't turn on and no lights display. I veryfied that the outlet works. I took it at my local Eletrolux store but they don't deal with this model. They told me that this model is made in Europe and they don't support it. Where can I take it to be looked at or do you have any ideas what the problem might be. Last time I used it it was working fine. Thanks, Rodi

... Electrolux Oxygen Z5540 Pet Lover Vacuum

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!

Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

Let's try this again. The main vacuum and hose works fine, the "foot" does not. When I turn it on, it shuts off automatically and the light comes on telling me to "check brushroll". I did this and removed all hair, strings, etc., Still won't work. Please respond. The last post took over 30 minutes with no response.

Sounds like you have hair or carpet buildup in the roller and it is not freely rotating and you are getting an error. If there is no buildup, then roller bearings may be frozen up, or the unit has a faulty capacitor and is not going to work due to el ... Vacuums

My shark just stopped working. It was working just fine last time i used it. Now when I plug it in nothing happens. What can I do, help my floors are crying for attention.

No sound no nothing!!! Well or the buttons, or the wires, is not connecting, unplug and try 2 fix it or call 911 :) Am kidding, or someone who knows about it. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Nothing happens when i turn on my vax 6131. The machine worked fine last time used and the fuse is fine.

... Vacuums

The brushes are not spinning at all. I have checked them and they are snapped in securely. It was working fine last time I used the machine. I have cleaned them and they spin manually just fine.

You probably got a piece of foreign material jambed in there for a moment and it "smoked the belt" that spins the brushes,it will either have the belt on either side of the brush housing cylinder or like kirby vacs the belts around the cylinder and i ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My bissell proheat will not shoot water out of the carpet cleaner or tool cleaner. Checked belt and it is fine. I worked just fine last time i used it, which was about 1.5 weeks ago.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Pickup water wont pickup the water after putting it down very little comes up into the tank .it worked fine when we baught it but after not useing it for some time it worked now it wont **** water up at all can anybody help.

The clear shroud covering the front of "hood" has two sheet metal type screws at the bottom in front of the brushes, these two screws also hold the little straight brushes ( one on each side) in place. I found one of these screws had broken it's plas ... Hoover F6020-900 SteamVac Upright Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.

Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes do not turn worked , fine last time i used it a month ago.

The brushes are run by vaccum. Take the brush out and there is a passage way in there that could be blocked. If I rememer correctly there is a screen in there. If that dont help then there is a spring hooked to a lever underneath so when you lay the ... Hoover F7220900 SteamVac V2 Upright Vacuum

Shop Vac was working fine last time I used it. Now I try to turn it on and nothing. I have cleaned the terminals on the toggle switch. I know there is power to the switch

Try tapping the motor area with a piece of wood or something, damp usage may have seized it up a bit ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1450 seconds