Having problems with your Filter Queen Majestic Canister Vacuum ?

Power cord worn out where it enters motor, have to move cord certain direction and will turn on. Cord finally gave out one day and almost shocked me when it literally blew out. wont turn back on


Answers :

You have popped the fuse in the plug top or have burnt out the wires in the cable
\015\012
\015\012No matter you have got to shorten and re-wire the cable into the cleaner or get a new lenght of flex and do the same thing.
\015\012
\015\012Some are easy to re-wire some are a pain
Repair Help & Product Troubleshooting for Filter Queen Majestic Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Power cord worn out where it enters motor, have to move cord certain direction and will turn on. Cord finally gave out one day and almost shocked me when it literally blew out. wont turn back on


You have popped the fuse in the plug top or have burnt out the wires in the cable \015\012\015\012No matter you have got to shorten and re-wire the cable into the cleaner or get a new lenght of flex and do the same thing.\015\012 ... Filter Queen Majestic Canister Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

My kirby is shorting out when i plug it in and turn it on it wont turn on and then after a little bit it will turnon but twhen you move it it will turn back off.. and there were sparks from the cord.... i was wondering if i still have a warrant to get another one ive never had a problem with my kirby i love it but am dissapointed that i cant use it


... Kirby G5 Bagged Upright Vacuum

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hi, A few days ago I bought a Philips hairdryer (HP4935/22) & have used it only twice. Somehow when I used it this morning some of my hair got caught in the filter at the back of the dryer & the motor slowed down & I think overheated & stopped. Normally the filters come off but I don't think this one does. I haven't turned it back on so as not to possibly damage it even more. I am quite upset as I really love this hairdryer. It's quiet, light, small, powerful & does the job brilliantly. I h


This is usually a safety feature so it doesnt burn itself. If there is a lot of hair in there try pulling it out, and if there is a little try with it too, if you can try get it out with something. If you think there isnt any in there anymore, try to ... Philips Vacuums

One day, I pressed the "on" button and it didn't start...had no problems whatsoever before.The inside hose is clear-fan turns-no visible breaks in the electrical cord or plug...


You need to measure for voltage inside the machine between the white wire and black wire from the power cord. If zero, the cord is likely broken at or near the plug end. This is a common problem if one pulls the plug by yanking on the cord instead of ... Kirby Generation 3 Bagged Upright Vacuum

Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to


When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums

Water leak I just bought this steamer a few days ago, and already I am having problems, when I fill the water tank that your suppost to fill the water runs out before I even turn the machine on. I have tried using plugs to keep it from doing this just so I can shampoo my carpet, this seems to work to a point, considering the fact that there are two holes underneath close to the brushes and one just a little ways back from that location. Do you know if this is something that should have plugs or


If you just pruchased this, then it is under warranty, take it along with proof of purchase to a warranty repair shop and have them fix it. If water just runs out, then there may be a seal missing or a water line off. ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re


Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum

Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.


Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hot cord the cord on my vacuum cleaner has been getting very hot the heat is from one end to the other incuding the plug and also where the cord exits the back of the canister please help I love this vacuum cleaner it has been faithful to me for over 15 years!


Likely after all these years that the motor is starting to go bad and draw more amps thasn it should. a new motor at a vac dealer is your best bet. it was likely made by panasonic, so a new panasonic is your best bet, and less $$$than the kenmore for ... Kenmore 23313 Whispertone Bagged Canister Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron


The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Hi: My DC14 (not animal version) has 3 major cracks that have pretty much killed the thing. There are three 'columns' that run down from the handle to the base. From the back, the left one has either the intake or outflow for the canister and the right one has the reverse. The middle one is where the base of the extension hose and cord is mounted. On all three the plastic has cracked at about the point where the bottom of the canister meets the permafilter. The vacuum is useless now and


I'd suggest using an epoxy cement (3M makes really good stuff) The epoxy comes in 2 separate tubes or bottles. Each alone will do nothing, but when combined become incredibly strong. Use care when using since on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!


Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad?


My first recomendation would be to try pluging into a diffrent wall outlet as well as something that is on a diffrent circut . It is a known problem that the pins inside that make the connection could be worn out . There are several pins from the one ... Kenmore 21513 Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

I have a Hampton Bay ceiling fan St. Regis model #138 498. Somehow the remote got messed up and now the lower light flashes on/off when the power is on and nothing else works. This happened one other time and I simply turned off the switches and when they were turned back on everything worked fine. This fix does not work this time.


... Vacuums

LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough


The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum

My Hoover Windtunnel cuts off after using it for a few minutes. After an hour or so, I can turn it back on again. This keeps happening every time I use it. This is my third one. I have taken the other two back to Target for the same problem and they have exchanged them.


Yes this machine has a thermal protector in it to shut off the machine if it gets to hot, this is normal. if there is no clogs in the hoses or in the machine then you will need to wash the filter at the top of the machine. you will have to remove the ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!


... Hoover Vacuums

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0737 seconds