Having problems with your Filter Queen Majestic Canister Vacuum ?

There is power but the motor seems to not turn, therefore, there is no movement via the rollers. please help

Answers :

Hello. On the back of the power nozzle, there is a little red button. With the unit turned on, press that button. If this does not re-engage the brush motor, then, turn off your machine. Turn the roller manually, does there seem like there is any resistance, or does the roller spin freely? If there is no resistance, your belt is broken. If you have a new belt, unscrew the screws that are marked"for belt access" this will release the rug plate for belt replacement. If the roller had resistance, then , check the cords on the wand. There are three places that your cord could be unplugged. The machine where the hose plugs in, the power nozzle base, and the hose/wand connection. I hope this helps you! Thanks, Rene
The belt which turns the roller brush is probably worn and therefore not turning the roller brush. You can get a replacement here:

Filter Queen Majestic Replacement Belt
Repair Help & Product Troubleshooting for Filter Queen Majestic Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There is power but the motor seems to not turn, therefore, there is no movement via the rollers. please help

Hello. On the back of the power nozzle, there is a little red button. With the unit turned on, press that button. If this does not re-engage the brush motor, then, turn off your machine. Turn the roller manually, does there seem like there is any ... Filter Queen Majestic Canister Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!

There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ

I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

I recently purchased a Sunbeam Artista EM5900 model coffee machine. I plugged it in and pressed the 'Power' button only to find the power go out. I understand this is short circuiting, so I went and turned the power back on. I then moved the machine to a different powerpoint and plugged it in - the same problem happened and I have tried it countless times on various other powerpoints. Help please?

Try it in a different part of the house. If it works then you have too many things running in the kitchen.\015\012If it still blows a breaker then it is shorted out and needs to be returned. ... Vacuums

Radio will turn on....bought new power adaptor but still have problems. It did go on, but after turning odd will not come on again Can you help please

Hi,The receptacle inside the radio for the power adapter goes bad/worn or a wire comes loose inside the radio. You would have to find a new power adapter receptacle...take the radio apart and then solder out the old and in the new to repair the ... Vacuums

When I turn the vaccuum on the roller works for about 20 seconds, then I hear an awful, loud noise, and the roller does not work. Sounds like maybe some gears are being stripped? Please help

It sounds like you need to change the belts. You can get replacements and view the manual here:Dyson DC07 Belts and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.

... Vacuums

HOOVER SAVVY This is less than a year old (yep, no receipt) and all of a sudden last night the vacuum turns off after a moment of running. Also the red and green lights do not work at all. I've thoroughly cleaned the bagless unit, and it still won't work. It powers on for a split second then turns itself off. Help please.

I had the same problem. Took it in and the repair shop they said it was the switch. It was an $18 switch and $30 labor. Switch was a red on/off button with 2 wire leads and caps to screw on for connection. If you can wire a ceiling fan then this ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a hoover Core vacuum. The problem is that the blue light flashes (as normal) when it is plugged in and the power is turned on and the blue light stays on (as normal) when you turn it on at the button but it makes no noise and doesnt work. All of the filters are clean. Can you help please?

... Hoover Vacuums

How do i know if my power button is not working on my diamond edition ultimate g kirby vac? It was fine when i changed the water and went to turn back on it does not power on, neither will the button click. please help

Make sure the water reserve all the way on it may not be cliped on all the way ... Kirby Ultimate G Bagged Upright Vacuum

Kenmore vaccuum upright moded#721.33289030 vaccuum worked just fine turned it off for a minute turned it back on the light comes on but theres no power from the motor Please Help thanks Valerie

... Vacuums

The power button will not turn off my dyson dc25. Please help. Thanks

Switches on electrical components aren't made for a lifetime. They want it to last for a long time but there is possibly a factory fault in it. Either way you'll need a new switch put in it. If you send it out for repair you'll find out it's not che ... Vacuums

No power. electric is OK. system will not turn on. Please help

Detach the vac itself from low voltage thin wiring leading to the house. With the vac plugged into power, try the manual switch and then try shorting across the low voltage exterior terminals with a rubber gripped set of pliers. If you can hea ... Broan-NuTone CV353 Central Vacuum

Have model UH70085 and went to hoover.com and they had no replacement for the very thin belt that turns the roller I brought the belt number stamped on it to home depot and they could not help. Can you? Please advise.

See if you can find a generic brand. Had the same problem with mine but found one at kmart that worked. Or try finding it on the internet. ... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

I can't find my manual for my Hoover F6060-900 steam vac; therefore I can't figure out how to turn off the tool feature and water is pouring out of the hose. Can you help me please? Sincerely, Bob damron

Manuals can be downloaded from the Hoover website ... Hoover F6020-900 SteamVac Upright Vacuum

My Dyson is getting the suction power but the black roller is not turning? Any suggestions, please?

Which Dyson model do you have? Some have a reset button for your roller. If that is the case try hitting that button and see what it does. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

You might not believe this but i don't know how to turn it on. I thought it was on the power nozzel but It is just got an orange light on. I know this sounds silly but please help me.

The on/off switch is located on the hose handle. The "O" is for off, "I" is vacuum only, and "II" is for vacuum and power nozzle. The light below the switch indicates there is power to the vacuum.\015\012If your vacuum doesn't run, there are ... Electrolux Guardian Bagged Canister Vacuum

We have a jvc nx pn10 ipod dock. Every time we turn the power on it says "Hello" briefly then P-ERROR. Nothing will remove this message. Can you please help?

(This question should not be in the Vacuum section - the device in question is a Clock/Radio/iPod dock) I had just this problem but could find no solution on the Net. JVC could provide only a PDF of the manual, which nowhere mentions P-ERROR. So, w ... Vacuums

Roller I recently removed my roller to cut all the hair off it and when I replaced it everything snapped right in but when I turned the power on the power worked but the roller wouldn't turn

Hi.\015\012\015\012Did you put the drive belt back on the roller ? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum


Spinning filter? Do you mean the brush? If its the brush you just have to replace the belt. Click on this link so you get an idea. ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!

The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

After turning on power , brush roller freezes and indicator light turns red

Try turning the roller by hand UNPLUG VACUUM FIRSTit should turn very easy, otherwise it is bindingall uprights have this problem eventuallyhair and fibers get in roller bushing and seizeluckily disassembling is relatively easy, same ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.

The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7981 seconds