Having problems with your Filter Queen Majestic Canister Vacuum ?

Electrical cord electric cord connection to cannister boby on filter queen is fixed by a plastic grommet or connection - how does this go into place without breaking or forcing plastic part?


Answers :

It has a **** shell like closure on the inside and can normally be popped out by squeezing with pliers. It will have a slightly oval appearance, you must squeeze it round and pull.
Repair Help & Product Troubleshooting for Filter Queen Majestic Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Electrical cord electric cord connection to cannister boby on filter queen is fixed by a plastic grommet or connection - how does this go into place without breaking or forcing plastic part?


It has a **** shell like closure on the inside and can normally be popped out by squeezing with pliers. It will have a slightly oval appearance, you must squeeze it round and pull. ... Filter Queen Majestic Canister Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

Want to replace connection pipe part #KC92PBZTZV06 that goes into the cannister. Want to seperate it from adapter #4370325 without breaking it. I have the new connection pipe.


... Kenmore Vacuums

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Replacing water pump on Bissell Power Steamer Pro #1697-m How do I disassemble without breaking plastic parts?


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a dyson dc all floors and I need a new bottom brush, will I be able to replace it myself without breaking any plastic parts,if I order the brush online?


I would say to take it into a shop. Don't try it yourself Dysons arent any vacuum you can just go into target and buy for 50 bucks. there not made to just be taken apart. ... Dyson Vacuums

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?


I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

Meile Solaris. Power cord connection faulty. Unit powers on/off when cord is being retracted/pulled out. Maybe a break in wire close to connection point in vacuum. Or, the connection point itself is loose? The problem likely resulted from trying to use vacuum at furthest extent of cord.


Cord reel likely needs to be tightened. requirs disassembly and large washers installed to keep reel connections tight. Jim ... Vacuums

The water dispenser must have been left plugged in and the hot water switch on without any water bottle on the unit because a plastic part inside got warped and now the unit tries to heat the whole 5 gallon jug of water. I want to replace the inside plastic part but I don't have the manual and don't know which part no. to request or where to send my request for parts.


Please state the brand and model number of your water dispenser, so I could give you the exact part and lead you where to purchase it.Post back ... Vacuums

I have a simplicity f3500 and while vacuuming the plastic part of the motor with the blades broke off, (the end plastic part of the motor....where can I buy that part without replacing the entire motor? Jodi


SURBAN VACUUM 315-4543111 ASK FOR KEN ... Simplicity 7850 Premier Bagged Canister Vacuum

Chain tensioner Is it possible to change the chain tensioner of the Husqvarna 240 to a tool less chain tensioner or at least to the chain tensioner where the adjustment screw is accessed from the side not from the front. The problem is that there is a little plastic part that breaks rendering the chain tensioner useless. I have changed it twice and it keeps breaking. To change it you have to change the whole part that covers the break and chain mechanism.


... Husqvarna DMS 240 Core Rig - DMS 240 w/ Vacuum Pump

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

I cannot fit a Miele SF-AH 50 Active HEPA filter into my S524 Miele vacuum. It doesn't seem to have the rear tabs in the right place to push it into place all the way. When I put it into the place, the top won't close. I'm afraid I'll break something if I force it down. What is wrong?


... Miele S524 Mercury Bagged Canister Vacuum

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.


Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.


... Electrolux Vacuums

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?


... Vacuums

Hoover steamvac F7226900. Bottom of clean fill tank cracked, how do I take off the black plastic piece around the bottom of the tank without breaking it? Thanks!


Try this link belowhttp://www.ereplacementparts.com/hoover-f7226900-steamvac-parts-c-37315_37419_202371.html ... Vacuums

We have had three belts break on your hoover vaccum cleaner u5472-940. It is easy to replace, you just remove the plastic part over it, put belt on wheel and then put it back on. Any idea on why the belt keeps breaking?


Sometimes when you buy belts from the walmart or target, they are not at the correct specification and they brake as soon as you turn on the machine. i would suggest that you buy these belts from the company. ... Hoover F6021-900 Steam Vacuum

We ran our 9 gallon Ridgid without a filter (Silly boy) Now I need clean the exhaust. The entry to which is clogged. Any easy way - without breaking it, to removed the plastic mount the filter fits on to.. ? Please.


This video may help you ... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

I have owned 4 sebo uprite vacs. Every one of them has the same problem. Where the handle connects to the vac it break contact and shuts off and on. It seems the connection between these two parts is very weak. The only answer I get from my local repair shop is


Well you now know the error of your ways, don't buy another!The best fix is to remove the connectors and connect the wires directly together. ... Century 400 UVAC Vacuum

I'm using a Eureka maxima 12 amp vacuum and where the hose is connected to the vacuum by a screw that part is broken where do I find a replacement hose that includes the clear plastic part that I can attatch to the vacuum?


... Eureka 4700A Maxima Bagless Upright Vacuum

I have a yellowMiele Vacuum,model=Electronic Air Clean Plus S3121. On the main body the part that the pipe/nozzle clicks into has a piece that has snapped off. I can see this by lifting the lid and the black plastic piece that is screwed to the inside of the lid has a piece chipped of it which means that when the nozzle is clicked into place it is completely loose. There is a black piece that clicks into the inside of the hoover into this broken part which is still ok so at the moment by linin


Generic problem for all Vacuums\015\012I have a yellowMiele Vacuum,model=Electronic\015\012posted by maura497 on Apr 18, 2008\015\012Report abuse\015\012 ... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

I lost the detergent container on my Hoover Model F7220-900. Its a small plastic bottle that sits on the back of the clean water tank. I called the help desk and they told me that they no longer make that part so I have to pay $55 to replace the whole tank which will come with a detertent container built in. The whole carpet cleaner was only worth about $225 new. I don't feel I should have to pay $55 for a part I don't need but the machine is worthless without it. Any good ideas to solve th


... Hoover F7220900 SteamVac V2 Upright Vacuum

How do I remove the collar to replace the cord to the power bar, I have the part, cannot get the little collar off to connect the new wire, purple to white and white to black... cannot get the old wir


... Hoover Powermax S3530 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0504 seconds