Having problems with your Filter Queen Majestic Canister Vacuum ?

The electric Foot keeps losing power have tried cleaning the arm connections but I think its in the foot itself

Answers :

The problem may be in the motor itself, there may be a loose terminal screw or wire nut that makes the electrical connection to the power head motor. The motor in the power-head consists of two wires it is just a matter of disassembling the power-head. If the motor was shorted it would not function at all. Also check the strain relief of the pigtail lead that attaches the wand to the power-head.
Repair Help & Product Troubleshooting for Filter Queen Majestic Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The electric Foot keeps losing power have tried cleaning the arm connections but I think its in the foot itself

The problem may be in the motor itself, there may be a loose terminal screw or wire nut that makes the electrical connection to the power head motor. The motor in the power-head consists of two wires it is just a matter of disassembling the power-he ... Filter Queen Majestic Canister Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet

I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a new bissell 50c9 upright vacuum and it keeps clogging in the clear window in the back. there is a flap that keeps coming open and filling up. everytime i clean and restart, the flap opens. i tried holding it closed and noticed lose of suction.

... Vacuums

Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee

... Vacuums

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou

Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?

I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.

Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett

I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums

I have the scunci 1000 steamer- it was sitting for a while and the cap on the top looks like its corroded and i cannot remove it from the steamer - i just bought it a year ago, but i think the salt or vinegar from cleaning it got trapped in the top and i tried everything i could think of to loosen the top so i could pour water into the unit and use it again; otherwise it is in perfect condition, but i tried even pliers and i cannot loosen it and i dont want to break it, but am so frustrated - wh

Hi, Elaine, W/D here.Corroded items are difficult to break loose as the corrosion builds up a layer that binds the parts together. Try this, as I usually have good luck with this method:Tap around the perimeter of the cap with a wooden h ... Scunci SS1000 Handheld Steam Cleaner

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.

I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.

Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped

... Electrolux Guardian Bagged Canister Vacuum

Kenmore Powermate foot pedal doesn't adjust the height anymore

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Ok so, here's my problem. I have a nintendo DSi and I'm trying to connect it to the internet. I've been searching on google on how to connect it. They said that i need wi-fi and some say I don't need wi-fi and some are saying i need a wirelerr router and some are saying that I don't need a wireless router. I'm wondering how I should connect my DSi without a wireless router and without wi-fi.

Http://www.nintendodsi.com/meet-dsi-xl.jspI think you are trying to do the impossible but try this site. ... Vacuums

I've recently bought a hitachi HDR505 & haven't had a problem using it with an indoor ariel other than the fact in bad weather conditions there have been problems with the signals. So I tried to attach the ariel wire that connects from a box in the corner of my living room which connects to the outdoor ariel but cannot connect it into the 'ariel in' compartment on the box as it does not fit into that hole but does fit into the 'ariel out' hole. Please could I get help with a solution asap as I w

... Hitachi Vacuums

Meile Solaris. Power cord connection faulty. Unit powers on/off when cord is being retracted/pulled out. Maybe a break in wire close to connection point in vacuum. Or, the connection point itself is loose? The problem likely resulted from trying to use vacuum at furthest extent of cord.

Cord reel likely needs to be tightened. requirs disassembly and large washers installed to keep reel connections tight. Jim ... Vacuums

Rainbow shampooer The soap dispenser on my Rainbow is not dispensing soap when I flip the switch to 'soap' mode. All connections are intact. All plastic hoses are intact. What do you think is going on? The soap bottle connects to a little straw that appears to be free of obstruction, however, it connects into a sealed casing on the hose.

The little "wash/rinse" switch on some of the Aquamate units shuts off the soap flow by kinking the tube inside the housing. If you leave the switch in the rinse position (therefore, kinked) when you're done using it, it may dry in the kinked positi ... Rainbow E series Canister Wet/Dry Vacuum

How do I replace foot lever that keeps vacuum standing up

... Bissell 3522 PowerForce Bagged Upright Vacuum

Vacuum Problem My dirt devil vacuum is losing suction and keeps clogging. All the dirt keeps sticking to the screen by the filter and then it would stop working. Also the hose does not have a strong suction power either. So what can I do?

The Bissell can have several filters in it, depending on the model. Some have a round hepa filter that is covered with a foam sleeve. This filter is located at the bottom of the dirt cup. Others have a foam filter that is located under the dirt cup i ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Am i going mad? I've just brought an electrolux Cyclone Ultra 2000W hoover. I've got it out of the box and have tried to fix the cover to the unit (i.e the bag free area which collects the dust). It won't fit. I've tried everything and think it must be faulty. Has anyone ever come across this before? Grrrrrr.

Take it back to the store and compare it to another one, and possibly have a store manager help you, if they can't get it, then they should give you a different one and make sure that it will work before leaving ... Vacuums

TRYING TO REPLACE THE PLUG ON An ELECTROLUX Z5915 1600W vacuum cleaner, IT HAS TWO WIRES from the cord.....BROWN AND BLUE.....BUT 3 POSSIBLE CONNECTIONS ON THE PLUG NOTED N, L and the earth connection.

... Electrolux Vacuums

Our Bissell ProHeat carpet cleaner is not working. The power is connected because the red heat lamp is on, however when you touch the foot pedal for the start of the rollers, the power is not connecting. Short somewhere??? How to locate the short? Please advise. Thank you.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Was vaccuming and vaccum quit. Tried unplugging and turning back on. Getting absolutely no power. unscrewed screw under handle and tried to make sure connection was being made. Don't really know what to do.

Ok..If you have a multimeter you can check plug fuse then switch and motor, if you put leads across the plug you will get some reading if its working.could be thermal cut out on the motor. ... Kenmore Magic Blue 24195 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0504 seconds