Having problems with your Filter Queen Majestic Canister Vacuum ?

How do I change the electrical cord? It has broken off right at the unit.

Answers :

If you can disassemble the vacuum and get to where the wire goes into the machine, you can probably repair this.
\012Once you locate the wire inside the machine, you either have to disconnect the wires from the switch at the terminals or if there is a place where there is room you may be able to use wire nuts to splice the wires together.
\012Strip the cord coming into the machine, remove about 1/2 inch of insulation from all wires and connect matching colors.
\012Use normal electrical cautions.
\012Let me know how you do or if you have more questions?
Repair Help & Product Troubleshooting for Filter Queen Majestic Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I change the electrical cord? It has broken off right at the unit.

If you can disassemble the vacuum and get to where the wire goes into the machine, you can probably repair this. \012Once you locate the wire inside the machine, you either have to disconnect the wires from the switch at the terminals or if th ... Filter Queen Majestic Canister Vacuum

Electric cord I need to know how to change the broken electric cord on my Fantom.

Welcome i nead electric directions for Panasonic MC-V7720 because I do not know which cable I have with myself connect.PLESS HELP MY. ... Vacuums

Have an older model Electrolux canister model. The electric plug is broken so I got a new plug to put on. When I cut the cord to replace the plug, the dang cord retracted into the unit. So how do I get access to the cord area so i can find the end to the cord!

Hi,\012\012You have to open the vacuum cleaner and look for the wire.\012\012It is located inside the circular wheel, where it wind itself up.\012\012Don't be afraid to open it, unless your willing to pay somebody just to install a ... Electrolux Vacuums

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it

It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

Dyson dc33 multifloor - change electric cord

... Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech

... Vacuums

How do I change the electric cord on my Kirby vacuum?

Hello, younghI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ... Kirby G4 Bagged Upright Vacuum

Got a Filter Queen Majestic Limited Edition, the one with the high and low power switch, an I have to change the power cord. How can I open the main unit to reach that power cord? Thanks,

First remove the top cap under your handle. \012Then, remove the three screws under the handle. \012remove the rubber cover on the switch\012undo the clamps on the side of the unit\012lift off the chrome cover with the cord on ... Filter Queen Majestic Canister Vacuum

The unit is not powering on, I have changed the plug and opened up the unit to ensure all the electrical connections look ok..Is it the heater element?

Hi,Yes, they burn out easily...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Broken electrical cord

The belt can e replaced but I recommend you should take it to your local vacuum cleaner service center. They may even be able to fit a new plug on the end for you if the damage is at the plug end. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Wadvark 7907 Hi I have a Wadvark vacuum cleaner Prestige edition model 7907, and I need to know how to disassemble it as the power cord is broken where it goes into the wind-up part of the unit. Cheers, Tony

... Vacuums

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it

The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Needle rubbing I have a singer pro finish and recently I broke a needle and the lower looper also busted clean off. I ordered the lower looper and replaced the broken one and changed both the needles. Now when I turn the hand wheel and the lower looper moves to the left and the needles descend they pass in front of the looper but when the needles begin to move up and the looper moves back to the right the needles bend back and go behind the looper. Help! Thank You!

... Singer 14CG754.CS Pro Finish Industrial Commercial-Grade Serger

How to change the electrical cord on a dynamite dirt devil

... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

How do i change the electric cord on my g4 kirby vaccuum?

... Kirby G4 Bagged Upright Vacuum

I got as vacuum sealer at a yard sale - I don't know the brand/make/model to find instructions for it.It is electric - has a cord to plug in - white - 2 lights on front - 'seal; ;vacuum' under unit is a model # - BS-828

... Vacuums

How do I attach the rainbow mate to the rainbow canister or wand? I have the D4C model, My electric hose is original but does not have the grip handle. Does that matter? The cord is so short it cant just attach to the canister right? thank you very much.

... Rainbow 75th Anniversary Canister Vacuum

Need to change electrical cord on g5 kirby - Kirby G5 Bagged Upright Vacuum

This should be fairly easy to do. With the cord unplugged, take the screw out that it holding the hard plastic cord cover onto the base of the machine. This is where the cord looks like it's going into the bottom of the machine. The next part is a bi ... Kirby G5 Bagged Upright Vacuum

My gtech sweeper has broken down. It is an electric rechargeable one and it just has no power. We have changed the fuse in the plug. Help.Lost receipt so no entitled to warranty.

It probably needs a new battery and it would just be cheaper to get a new vacuum ... Vacuums

Change cord on electrolux EL5020

In order to get to the cord that is disconnected you need to remove the screws that hold on the frame(the red shell). You will need to remove the "fenders" that are near the wheels. In order to remove the fenders get a flat tip screwdriver and pry ... Electrolux EL5020 Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce

I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators

Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums

Having trouble with electrical cord.

Greetings from GoVacuum.com, I'll tell you that 9 times out of 10, when a Kirby Generation doesn't turn on, it's the cord that needs to be replaced. This is by far the most common problem that we see on Kirby repairs. The Kirby moto ... Kirby Ultimate G Bagged Upright Vacuum

Changing belt Please advise how to change the belt. I wasn't the person who took the belt off, didn't watch. Now it's just me and the belt. I had 2, but 1st one burnt right off. Apparently I didn't have in the right spot! don't want to waste the only other new belt I have. Pictures would be greatly appreciated!!!!!!! Thanks Tammy Can call 920-660-0680

Step 1: Lower handle to floor to change belt Step 2: Remove the two screws from the top hood on the footStep 3: Lift hood to remove Step 4: Lift right end of brushroll (the belt end) Step 5: Remove and discard belt.Step ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.7152 seconds