Having problems with your Filter Queen Majestic Canister Vacuum ?

Noise coming from inside

\015 If you run the vac for a short time it make a grinding noise.but still will ****,\015

Answers :

Repair Help & Product Troubleshooting for Filter Queen Majestic Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Noise coming from inside

... Filter Queen Majestic Canister Vacuum

When i turn my hoover on and start hoovering the cable inside makes a clicking noise and goes off and comes back on when i move the cable. I have only had it for 3 months

Almost certainly a warranty issue. Take it back to wherever you bought it. ... Numatic Henry Bagged Canister Vacuum

Loud noise coming from cyclonic cap

Sounds like you'v lost a rubber seal check this diagram on the link below see if you can see anything missinghttp://www.vacpartswarehouse ... Dyson Ball DC24 Bagless Upright Vacuum

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak

... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I have a Napoleon Pellet stove insert Model NPI40. When the fire burn rate is extremely low it seems to operate normally. However, when I turn the heat up even a little I eventually get a high pitched noise that seems to be coming from the convection blower. Changing the speed of the blower has no effect on the noise level. I cleaned the blower but did not remove it. There was very little dust on it. Cleaning had no effect on the volum or pitch of the noise.

My theory is based upon 1st hand knowledge with a newer EPA compliant freestanding wood burner, with the air-tight and high efficiency ratings.its possible that its just the high rate of air moving through the air chambers , similar to a o ... Kenmore Whispertone 23312 Bagged Canister Vacuum

Making high pitched squealing noise and motor is hot...cleaned out brush area and made sure hoses were free and clear too..noise is coming from the brushes because when I use just the wand, the noise disappears

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you

Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums

Hello i can turn my steam buddy platinum 44G258 on, water boils, press hand gun get a buzzing noise like you do with a jet wash, but no steam comes out, it seams the water is not coming through, have check the cap on water container thats ok, its where it releases the water to is seams to be where the problem is, i think ! first time we have tried to use it many thanks steve.

... Vacuums

My vax swift 1600, has began to make a huge rattle noise, no noise when brushes and belt is removed. Seems like the belt is rubbing against the side. Wondering if there is meant to be a screw or something to keep the belt in place and it has come off.

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

My keurig coffee machine makes noise like it is brewing, but water just drips out. De scale reminder is on, but with no water coming out the vinegar is sitting in there and not doing much- a few drips coming out with each cycle. this will take for ever to get through the entire container of vinegar -should I keep trying and see if it fixes the problem??

... Vacuums

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.

HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

November 2008 I bought a Simac Stirella 9000D steam generator iron. Recently its been leaking water out the bottom of the regenerator. It makes a noise when it is trying to get the steam to the iron and it works then but afterwards when the noise stops it stops steaming and I find a puddle of water underneath the regenerator. Also a little steam comes out of the water tank at the top. I understand this is happening because of scale in the base unit. Can I get something to get rid of the scale? -

... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum


I dismantled the cover, withdrew the gear drive assembly and found the bits that had come loose. The mechanism that selects neutral or drive had come away from its shaft. I simply put it all back together and tightened everything back up. Works a dre ... Kirby Heritage II Vacuum

Carpet cleaning brush noise. When put in carpet cleaning mode, a loud noise comes from the brush bar area. We see no visible obstructions and have cleared threads and hair.

It's likely that one of the brush roll bearings has worn out. This is not uncommon. I think you'll find that you have to replace both the brush roll and the sole plate at the same time. Dyson sell them together as a kit. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a hoover porta vac. that at first it would sometimes come on and sometimes not. It did completely stop coming on, so I have changed the switch and the cord but with no luck. Could you offer any suggestions or is this a motor situation. To my knowledge the motor was not making any noise. Your help would be greatly appreciated. Thank You, Molly Maid of NW Fla.

If this has had heavy use, the carbons in the motor may be worn. ... Hoover CH30000 Bagged Canister Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth

Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

We have just opened a De Longhi Icona coffee maker. We followed the instructions to start it, but when we press the coffee button (after the OK light comes on), it makes a loud buzzing noise and no water comes out. What do we do?

May be you may forgot to fill it up with water...... otherwise i request you to please read the manual book which was given along with machine so that you may get the appropriate solution ... DeLonghi Vacuums

Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us

Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do

I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

Makes a high pitched noise when turned on and suction is not as good as when new. How do you break it down to check the motor? I suspect that is where the noise is coming from.

... Vacuums

Hello, I got a used Kirby Sentria. When I run the vaccum and push and pull on the handle, I can hearing a friction type noise. I got up close to the vaccum and it is not the wheels or roller. It is coming from the base of the handle. It's like it is pushing on something on the vaccum body and is creating the noise. Maybe transmission? Is this normal, or is it something I should be concerned about? Thanks for your help!

Try new belt yours may be slipping ... Kirby G5 Bagged Upright Vacuum

I shut my vacume off to change its bag out. Now it won't come on. Oreck xl2. There were no noises before turning it off or any smells of rubber burning. Just won't come back on. Is there a reset button. What can I do?

An access panel mounted atop a vacuum nozzle base via finger operated latches. When the latches are undone the access panel is removed from the top surface of the nozzle base allowing access to the parts of the brush assembly. The panel also has a ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0532 seconds