Having problems with your filter queen power nozzel ?

how do you install the roller spring in power nozzel

it fell out

Answers :

Repair Help & Product Troubleshooting for filter queen power nozzel

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need belts I am in the middle of cleaning my carpet and need a power belt and roller belt. Who sells them locally. 30127 Powder Springs, Ga


If you local repair shops don't have them, I am sure they can order them for you. Just have to check you yellow pages, also under Sew and Vac stores, most offer service as well as sales. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Roller I recently removed my roller to cut all the hair off it and when I replaced it everything snapped right in but when I turned the power on the power worked but the roller wouldn't turn


Hi.\015\012\015\012Did you put the drive belt back on the roller ? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped


... Electrolux Guardian Bagged Canister Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.


The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.


... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.


Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

The roller on my power head does not spin consistently. So my vac is not picking up of course. The square end pieces and the rod that goes into the wooden roller seem loose. I tried tightening it but it still is not turning. Can I do a fix with glue or something till I can get a new roller?


... Rainbow E series Canister Wet/Dry Vacuum

Purchased a new, portable, vacuum this date. 4/24/08 at Gottschalk's. Got it home, unpacked it and installed attachments. plugged into a power source, and depressed the power switch, machine did not come on, used three different power sources to no avail. advise--- Reply to [email protected] asap


Being under warranty, I would take it back for an exchange. You don't want something brand new and it is dead on arrival. Either that or take it to a warranty shop for repair. You mess with it and that avoids the warranty. ... Vacuums

How does the cord winder spring install on a electrolux canister style vacuum cleaner?


... Electrolux Vacuums

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ


I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

Our Bissell ProHeat carpet cleaner is not working. The power is connected because the red heat lamp is on, however when you touch the foot pedal for the start of the rollers, the power is not connecting. Short somewhere??? How to locate the short? Please advise. Thank you.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

I sucked up a sock and there was a burning smell. I immediately turned off the power, the sock was wrapped around the roller, got it off and let the vacuum cool. Now it no longer powers on. Is it dead or fixable?? Ann Marie Smith


The smelling could be the belt. Unplug the unit and turn it over, see if you can see the belt. Turn the roller to see if there is any wear on the belt. If the belt looks good, that is not good. If it does not turn on, there is no fuse or breaker ... Euro-Pro NV31 Infinity Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have no power to the roller motor but if I disconnect and connect direct power, at the hand connection, it works. Is there a fuse somewhere I do not know about. If not what is the problem and solution? Thanks, Wayne [email protected]


If you have taken the handset and plugged directly to the head...you have already found your problem to be the hose.\015\012\015\012Either take the hose to local vacuum repair shop or test the continuity of the hose yourself. ... Beam Industries 2775 Serenity Plus Central System Vacuum

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?


Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

The power works, but the roller brush does not move. The belt is intact and the roller brush is free of debris.


... Bissell LiftOff Revolution Pet Vac 37602 Vacuum

I want to install a belt on the turbo power 2000 upright vacum cleaner , What do I have to do to install it. The old belt broke.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=564997\015\012Generic problem for all Vacuums\015\012I want to install a\015\012Posted by mcpo on May 02, 2008 ... Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f


Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

I have a GE 106766 Canister Vacuum. The belt on the power end stretched and I replaced it. Now the roller froze up and won't move. Where can I find a replacement roller?


Try this sitehttp://www.onlinevacuumparts.com/ps-328-7-ge-6850-106766-canister-power-nozzle-parts.aspx ... GE 106766 Bagged Canister Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.


Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

I had a house built last Sep. Oct., They installed a Hoover Windtunnel System. I can't figure out how to use in in the garage, were it is installed. There are no instructions and no power at the place that looks like were you would plug the hose in. The system came from Costco. Joy Long [email protected]


What model do you have? ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0530 seconds