Having problems with your foot switch ?

how do you splice a foot switch on a Heritage II

the new foot switch has slots

Answers :

Repair Help & Product Troubleshooting for foot switch

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Install new foot switch on Kirby Heritage II Vacuum


... Kirby Vacuums

I have a Electrolux canister model L-E (circa 1986). Won't turn on. I think the foot switch is broken inside. Was working fine - turned it off then would not turn on BUT foot switch sounded different, kinda hollow sound. Perhaps I'm reaching but wortha a shot? Mary


I have one of these LE models also. Yes, the on/off button is broken. I have had to replace it twice on mine. My local vacuum repair shop suggested NOT to use your foot to operate this switch, but just press it on or off with your fingers. That will ... Electrolux UltraLux 2000 Bagged Canister Vacuum

When i press the foot switch the machine does not switch on. Is there an internal fuse?


Don't think there is an internal fuse.\015\012If you have replaced or tested the plug top fuse & that's ok, it may be that the foot switch needs replacing or a wire has come loose from it. ... Kirby Heritage II Vacuum

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.


The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

When i push on the power button on it runs only as long as my foot stays on the on/off power switch once i move my foot it immediately shuts off?


... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Kirby intermittent power, sparks near foot switch, how do you remove switch? Coud just be a loose connections?


Lay handle down toward floor and remove case top screws and replace the switch you'll be money ahead ... Vacuums

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums

Kirby heritage model 1hd. wires fell off safety switch. Need color to position on switch


If your looking at the back of the switch were the wires go in. Starting from left to right. you will see letter below the hole were the wires go in. for example, Y , yellow or " R " for red. this should help. ... Kirby Heritage II Vacuum

Eureka m# 4704A red on-off switch (foot touch)won"t press down


... Eureka 6984A Bagged Canister Vacuum

Wiring foot pedal switch legend II


If I remember correctly,on the switch itself,each connector is letter coded.'W' for white,'R' for red,and so forth.The manual mostly talks about how to change attachments and basic operating,but not repairs. ... Kirby Heritage II Vacuum

Sparks came out of the area of the foot switch and


This is now a dangerous appliance and should be repaired by a qualified tec ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Electrolux 2100 foot switch


The owners manual is HERE: http://www.aerusonline.com/service/manuals.cfm\015\012\015\012But it does not show the inside of the foot/power switc ... Vacuums

The foot switch does not turn on the G4D Kirby vacuum cleaner.


Here's a link to a free guide! The switch is available at this site as well...there is a link in the guide to buy one. \015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

Brush doesn't operate when the foot switch is pressed to allow the system to engage the beater bar


I don't believe that these vacuums have a belt so the only thing that I can recommend is to unplug it, turn it over and see if there is anything obstructing the roller brush such as string, tinsel, rocks, etc. See if you can turn it with your hand w ... Dyson Ball DC24 Bagless Upright Vacuum

I was using my Heritage 11 vacumn with the hose attachment and the motor shut down like the power went off .When you push the switch on the housing the light comes on but the motor does not run.


Hi, the motor could be overheating. Most vacuums have a heat sensor that shuts the vac. off if there is a clog. Let it sit, feel if it's hot. If so you may have a blockage of dirt etc. Try to clear it, let it cool and tart it up. I hope this helps, i ... Kirby Heritage II Vacuum

I have an animal and after i turn it on, I press the foot release to turn on the brushnad it doesn't switch over.


My Dyson started making a loud noise when in "carpet" mode. After reading a ton of forums I thought it was the clutch assembly. Got a new one on eBay for a great price. Somewhat hard to replace, but thanks to this YouTube video, I was able to get it ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

My Heritage II just lost power in the middle of vacuuming. The switch will turn on but no power.??? What is wrong?


It could be the switch that has become defective (the 'feel' of the switch may be different, but needs to be checked with a meter). Another possibility is that the cord has developed a loose connection at or near the power plug. Turn the switch on an ... Kirby Heritage II Vacuum

Foot activated power switch will not remain on


This kind of switch will turn on the power when it's pressed down a little, but must be pressed down further for it to actually lock itself on. First, make sure that you're pressing it far enough. One way to tell is operate the switch with the vacu ... Vacuums

Kirby Legend II, How do you remove Foot Switch


There is a plastic pop in trim cover which surrounds the switch itself. It will peel off revealing two screws which hold the switch in place onto the underside of housing. However you must also remove the rear cone shaped motor housing by a ser ... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

Heritage 2 - black wire pulled out from motor assembly, comes from power switch. Where does it go? Need wiring pictorial and schematic/wiring diagram. Can anyone please help? Many thanks, Malcolm


... Kirby Heritage II Vacuum

Gear lever the drive / neutral lever gas come out of the back of my kirby upright diamond edition vacuum cleaner and also the foot on/off power switch is now NOT working either. I am in Maroochydore. Queensland. Australia. 4558


Http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM?ugid=10000000003752018 ... Kirby G6 Bagged Upright Vacuum

Microswitch sticking will start, but stop as soon as foot off the red switch lever


Replaced micro switch ... Bissell Vacuums

Wire diagram required for foot switch on Kirby Legend 2


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0240 seconds