Having problems with your GE 106585 Upright Vacuum ?

I need a "Bearing Assembly" for roller brush 61445-1,I Have a GE 106575

\015 Hello,I Have a GE 106575,and to make a long story short,I need the "Bearing Assembly" for the brush roller 61445-1. The roller brush is in perfect condition except for one of the "Bearing Assembly's". It is not practical or wise to replace the whole roller brush because of 1 removable part that went bad. That would be like throwing good money down the drain. I can assume the "Bearing Assembly's" on this roller brush will need replacing every so often. So I need to know where I can purchase the "Bearing Assembly" for the brush roller 61445-1.Thank You Very Much,EarlsOK\015

Answers :

Probably should just go to a repair shop and they should be able to order one for you, that is if they are available by themselfs. Or if you have a store where you live that sells vacuum parts, you could go there.
Repair Help & Product Troubleshooting for GE 106585 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need a "Bearing Assembly" for roller brush 61445-1,I Have a GE 106575

Probably should just go to a repair shop and they should be able to order one for you, that is if they are available by themselfs. Or if you have a store where you live that sells vacuum parts, you could go there. ... GE 106585 Upright Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

My Dirt Devil Model 088520 has a brush assembly that wont spin. How can I either change the bearing or free it up somehow? I have been searching for a new brush assembly part number 2860145000 but it

Try this link > http://dirtdevil.com/parts/category/brushrolls-uprights/ ... Dirt Devil Vacuums

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Need to remove the brush assembly Kenmore Intuition

... Kenmore Vacuums

Bearing on end of brush froze causing belt to break. I need to replace the brush and belt. Are there other belts in/on this model?

Hi there. there is a belt in the unit. the owners manual here will give a good guide on how to replace the unit.the ... Eureka 3041BZ Upright Vacuum

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL

... Bissell 1200A SpotBot Pet Robotic Vacuum

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?

... Panasonic MC-V7515 Bagged Upright Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr

Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Our vacum isn't picking up @ all.we did have some thread around the brushes, about an inch wide. it has an odor like it is getting hot. the vacumn is about 1-1/2 yrs old. we need help. thanks BETTY COX.

Hi, The most likely cause would be a blockage. If you remove vac hose, does it **** on your hand? secondly, with the vac unplugged, Can you turn the brush reasonably freely ? Is the drive belt on? ... Vacuums

I need a vacuum brush housing assembly for Dyson DC15 animal. Part of it is broken (plastic).

Http://www.espares.co.uk/dyson/dc15/p/1086/716/10\015\012\015\012Try the above link or do a search in google for "Dyson DC15 parts".\015\012Also, tr ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

New wide Bissell vacuum brush bearings locked up after 1 hours use. This is the second one same problem.

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Need help assembling fan mechanism on optimus 1 vacuum backpack

... Team International Pro-Team QuietPro BP Backpack Vacuum Vacuum

Where to find a service manual to assembly the motor of GM80 nilfisk vacumn cleaner? I have dismounted it to fix new bearings and now I need to reassembly it Thanks a lot

... Nilfisk GM 80 Bagged Canister Vacuum

I bought a Clean Broom Electric Co., Model #CBU_5 (SKU# 7986628) Vacuum Cleaner 31CX E 255344. I have need of the following parts 2 belts and brush bearing seals. How do I locate these parts or to find them to purchase them. Thank you for any assistance you can give Tom Freer [email protected] Manufacture Date 0906

I need a screw on filter for model cb9191j-10a vacuum from clean broom electric company. ... Vacuums

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab

(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Broken Brush on Hoover SteamVac Need to order new brushes

Yes you can order a brush block. It comes complete it is around $35. You can buy or order them at any vac shop or call me at my shop and I can ship them out.Josh 614.868.0799 m-f 9:30-6 sat 10-2 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert

... Panasonic MC-V9638 Bagged Canister Vacuum

Ball bearing in brush roller

These can usually be purchased thru a hoover dealer and are not expensive. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Need to replace motor brushes on Kenmore canister vacuum 116.25914503 - Getting lots of arcing at brush ends. Need tear-down steps to get at the brushes.

If you can see the arcing you are likely in the motor housing. The brushes are specific to the motor depending on RPM. Most brushes and motors in Sears units are supplied by AMTEK Lamb. The color on the plastic housing and stamped model # on motor w ... Vacuums

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.

... Electrolux Vacuums

My FEIN 9-55-'13 recently started making more noise and is now officially a "screamer". There also developed quite a vibration associated with the noise which made me think it was probably bearings. So I took it apart and found no detectable play or lateral movement in the bearings, they seem fine to me. So I thought perhaps the brushes. The rotor where the brushes ride is quite black but I can't figure out how to get to those brushes, although I don't really think they are causing the noise

This problem is only caused by one thing the motor bearings are noisy, I have never found any other reason, they may look good and fell good but trust me replace the motor and the noise ... Fein 9-55-13 Turbo II Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0704 seconds