Having problems with your GE 106766 Bagged Canister Vacuum ?

Burshes are no longer moving, vacuum still sucks


Answers :

The belt has broken. You can get replacement belts here:

GE 106766 Replacement Belts
Belt snapped.Replace.
Repair Help & Product Troubleshooting for GE 106766 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Burshes are no longer moving, vacuum still sucks


The belt has broken. You can get replacement belts here:GE 106766 Replacement Belts ... GE 106766 Bagged Canister Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up


Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums

Miele Champagne Vacuum Cleaner Model S548 I was using the vacuum as normal, moved locations so I plugged into another outlet & suddenly there was no power to the vacuum! I tried it in several other outlets, tried the reset button... & still no power to the vacuum. Any ideas what could be causing this? Any info would be greatly appreciated. Thank you!


Greetings from ,\015\012 \015\012This definitely sound like a cord reel issue to me. This is really the only problem that I ever see on a Miele vacuum cleaner. 9 times out of 10 the cord reel needs to be changed. If you purcha ... Miele Blue Moon Bagged Canister Vacuum

Carpet roller will not turn. Vacuum still sucks up dirt


It IS true that you can take the plastic cover off the top of the carpet head. But in addition to removing the two Phillips screws at the bottom, you have to manouver the wand release a bit. Loosen the screw and carefully pull the release back just a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

The brush roller on my vacuum will not move. I've cleaned it, checked the belt, but when I put the roller back it, it will not move...almost like it is in a locked position. Everything has been done correctly from the book yet, it still does not move. Any help PLEASE?


... Electrolux EL8502 Versatility Bagless Upright Vacuum

The roller brush is not moving the vacuum has suction it's just the roller is not moving. The belt is not broke i can see it is still intact. I was sweeping and i noticed it just stopped moving.


... Dyson DC28 Animal Bagless Upright Vacuum

MC-V7400D Vacuum Vacuum will no longer create a vacuum Changed filter and still does not work. Sounds as if it is working.


Blow in hose and see if it's clogged, possibly a belt is come off. ... Vacuums

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!


I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My hoover Savvy vacuum is no longer sucking up dirt- brush turns


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

It stopped working while vacuuming. Still getting power, compressor still working but not sucking.


I would look for a clog, or look for a broken belt ... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I by accident sucked up the corner of a sheet into the powermate of my vacuum. I turned the vacuum off and pulled out the sheet but now the powermate is no longer working (suction works fine) Is this something I can fix on my own?


These power heads have a kill switch on them. Not exactly clearly labeled. the kill switch reset button should be on the right side of the unit as you look down like you are using it. you may want to try pushing it with the power to the p ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.


Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

The suction in the hose of my 2 year old Dyson Animal vacuum is compromised. I may have sucked up a small cat toy or something. Regular vac still is fine. The hose "sucks closed" after a few seconds near the top. I love my Dyson! Please help.


Hi there, it sounds as though the wand handle is blocked. To test this, remove the wand handle from the hose and test the suction at the top of the hose. If its strong here, then you will need to remove the blockage from the wand handle. If the suc ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Vacuum is clogged. I accidentally sucked up a baby wash cloth with my new vacuum. I think the cloth is still inside but I can't be sure. How can I check it?


Turn the vacuum upside down and see if you can see the cloth. ... Vacuums

My vaccum has a 3 position handle. This no longer works, so I have to pick up vacuum to move it. Makes it hard to vacuum scatter rugs. It does not lock into place


What is the brand and model of the vaccum? the description i see says Hoover U6311930. When I check the info for this model it gives me maytag vaccum cleaner. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Dirt Devil Upright Bagless Vibe Vacuum no longer sucks


Sounds like there's a clog in the long hose that connects to the dirt canister. Remove the hose completely and check for clogs. There is a blue plastic piece that the hose is attached to. You can remove it by taking out the two screws in the back, ... Dirt Devil M087700SV Bagless Upright Vacuum

Why won't brushes move on Commercial Carpet Pro Vacuum Cleaner


Luvumuch48tj: Unplug the vacuum and lay it upside down on some newspaper. Remove the sole plate (bottom plate) with a screwdriver. Pull straight up on the brushes (called a beater bar) and remove the beater bar and belt. Remove the end ca ... Carpet Pro CPU-2T Commercial Upright Vacuum Cleaner CPU2T With On-Board Attachments

I want to know if it's possible to give back my kirby vacuum it's been months but i don't use it because i moved to a place with no carpet and i'm still paying for it


Sell it on Ebay... That would be the beswt things for you because Kirby does not except returns unless it is factory defaulted. ... Kirby Vacuums

I have a bissell power force vacuum and I just pulled the bag out to change it and when I put it back in it began blowing air out the filter on the side and is no longer sucking


Hello,\015\012Try checking the attachment hose for clogs. It should come completely off of the vacuum with just a few screws. Also, check the little hole underneath the brushroll where the dirt goes in. Hope this helps...\015\012Marci ... Vacuums

I have a windtunnel 2 vacuum. It sucked up a cord that wrapped around the beater bar. Now the bar won't turn. There was no smoke or sign of something burning. The motor still runs and there is suction but no turning. We have it apart but nothing is obvious. What should I check?


Check the actual beater bar for movement. I have seen the plastic melting, and bearings seized under such circumstances. Also I am unsure by your question, but the motor that creates the vacuum (sucking) is different than the motor that spins your ... Vacuums

I vacuumed a sock and it started to smell like it was burning. i removed the sock from the brush head. now it still sucks, but the brush doesn't roll anymore. any ideas how to fix it?


Change your belt. ... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1132 seconds