Having problems with your GE 106766 Bagged Canister Vacuum ?

I have a short in my hose for the GE 2 motor canister vacuum model106766 where do i get just the hose to replace it

Answers :


Here is a website for parts for your vacuum: http://www.appliancefactoryparts.com/vacuumcleaners/brands/ge/106766.html#Other%20Parts

I hope this helps. I was confused by your statement that you have a short in your hose. Are you saying that something is wrong in the motor or that you need a new hose for the vacuum? The above website whould get you a hose for the vacuum. For the motor, Do a google search for the GE homepage, then click on the customer service, or support tab.

Good luck,
Hope this helps, if it does, I would appreciate a vote or comment. Thanks,

Handie Andie
Repair Help & Product Troubleshooting for GE 106766 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a short in my hose for the GE 2 motor canister vacuum model106766 where do i get just the hose to replace it

Hi,Here is a website for parts for your vacuum: http://www.appliancefactoryparts.com/vacuumcleaners/brands/ge/106766.html#Other%20PartsI hope this helps. I was confused by your statement that you have a short in your hose. Are ... GE 106766 Bagged Canister Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

Need to replace motor brushes on Kenmore canister vacuum 116.25914503 - Getting lots of arcing at brush ends. Need tear-down steps to get at the brushes.

If you can see the arcing you are likely in the motor housing. The brushes are specific to the motor depending on RPM. Most brushes and motors in Sears units are supplied by AMTEK Lamb. The color on the plastic housing and stamped model # on motor w ... Vacuums

Can I get a replacement hose for an older model vacuum? Model VNB-7 canister? Just guessing I would say yes. How and where do I order this part? I have probably had this unit for 20 + years! [email protected]

... Metropolitan Vacuum Company Metro Vacuum Magic Air Deluxe 4.0 Peak HP Inflator/Deflator Vacuum

We just moved and the movers didn't pack my Miele vacuum, they simply transported it as is. Now the piece that is supposed to interlock from the hose into the canister seems to be missing. Can you tell me how to get a replacement piece?

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=730491\015\012Generic problem for all Vacuums\015\012We just moved and the\015\012Posted by trumbull on ... Vacuums

I am losing suction and it sounds as if there is a leak in the vacuum(I hear air rushing around). There is also a high pitched noise. Dyson dc07. Can there be leaks in the gaskets where you clean hoses and filter? are they replaceable. Does the noise suggest the bearings are going in the motor?Is it worth getting fixed?

It wont be a gasket problem - they don't tend to fail. \015\012\015\012A high-pitched noise can be a number of different things. That is too vague to diagnose on here with the description you have given. Can you be more specific? ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Looking for Replacement Motor for Bosch Ultra 1450W Canister Vacuum

If you are finding BB's. then the bearings are bad. You could pull the motor and take it to a place that rebuilds motors to see about replacing the bearings. If it is a Lamb or amtec motor, there is a number stamped on it, you can match up another ... Vacuums

I have a central vacuum system. When I disconnect the hose from a wall outlet the central canister does not shut down dispite my turning off the vacuum at the handle of the hose. The only way I can get the system to shut down is to pull the plug at the canister. What gives? Rob

What I'm hearing is the canister(Not the Powerhead) portion of the unit is running all the time unless you unplug it. this problem could be caused by a short in one of your low voltage lines running through the house. To determine that just unplug on ... Vacuums

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@

Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?

Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Kenmore canister vacuum 25812500 hose end replacement

... Kenmore 22822 Canister Vacuum

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy

Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.

... Kenmore EVO All Surface Floor Cleaner Vacuum

Hi. Bought a M3888-3 Royalcylinder vacuum from Lidl. Lost manual that came with it. Only had it 4 mths. Need new hose. Plastic hose has snapped near whereit attaches to metal hose. Can I get a replacement hose from somewhere in U.K.? I know the vacuum is from Germany.

... Royal Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.

... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

I need to replace the hose on my Euro Pro Shark canister vacuum EP722. After numerous searches, unable to find online. Looking for simular hose that will attachment to canister. What hose from another model or even maker will work? Thanks

Go to shark in GOGGLE. Go sharks wedsite, find your vaccum, click your hose. We have 3 mops and vacuum. No trouble getting parts and filters. Not high priced. ... Euro-Pro EP722 Canister Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?

Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr

Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

The hose,essential to the vacuum, came apart. I tried tape but to no avail. Purchased 6 weeks ago. can yousend me a replacement hose? It is a Durabrand Bagless Cannister Vacuum. your phone number on the box is disconnected. It is a 1200 watt motor and I'm assuming that VCH3301 is the model number. Thanking you in advance for any assistance.Sue Jackson

I'm sorry to inform you but we're not the right place for the replacement because are a site that provides help and we're not connected to Durabrand Bagless , So for you hose replacement concern better try asking that to the store or the person whom ... Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.

... Vacuums

Central vacuum Hello, my central vacuum motor just clicks when you insert the hose into the receptacle. Is there anything I can do besides get a new motor or unit?

If the central vacuum is clicking that means that the circuit breaker is working and trying to get the motor to run but the motor is not functioning. This means it's time for either a new motor or a new unit. Unfortunately there's really no way aroun ... Electrolux Central Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger

There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

How to replace just the Kirby 210097 Hose End For G5 Series Vacuum Cleaner to hose. can buy replacement but can not get the broken end off

Simple and rquires no tools. Fill your sink with hot water and set the end in water with attachment on it. Within a few minutes the end is soft enough to slip out. setting the hose end in the water again will let you simply slip the hose into the ... Kirby G5 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1452 seconds