Having problems with your GE 106766 Bagged Canister Vacuum ?

No suction for use of crevice tools, running hot, then shut off

\015 No suction on hose when using crevice tool, power nozzle seems to work as I can hear sand going up the hose. When I remove the hose and electrical cord attached to canister and put my hand over the outlet on the canister I get good suction. There is no way to clean the hose or detach from power handle. The vacuum over heated and shut off Why?\015

Answers :

Obviously no suction in hose would indicate a blockage, over heating is a breaker that shuts off the machine when it over heats. There is no way to clean hose the on this model because the hose does not detach at either end, therefore I had to employ the use of the good old wire hangar. Job complete up and running, with good suction. It is amazing what a prayer to God can do.
Repair Help & Product Troubleshooting for GE 106766 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction for use of crevice tools, running hot, then shut off


Obviously no suction in hose would indicate a blockage, over heating is a breaker that shuts off the machine when it over heats. There is no way to clean hose the on this model because the hose does not detach at either end, therefore I had to emplo ... GE 106766 Bagged Canister Vacuum

Nothing inn the canister after using,suctione working,bottom roller working,no air leaks from hoses.Also when running awhile it shuts off by itself,have to wait awhile to use again


I'm not sure what vacuum you have, but that sounds like a blockage to me. Thermal shut off kicks in, shutting the motor down, to prevent damage from overheating. After waiting like 1 hour it probably comes back on. Make sure hose, filters, bag (if an ... Vacuums

No suction My Hoover Wind Tunnel vacuum runs but there is no suction. The last two or three times I used it, it shut itself off after having a burning smell. When I unplug it for the suggested 30 minutes, the motor will run again but no suction. What is wrong?? Should I just buy a nve one? This one is 8 years old.


Sounds like your motor bearings are going bad. This is generally indicated by the motor overheating, and the heat transferring out through the motor pulley, which is where the belt attaches. So, your machine is overheating, melting the belt, and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Little suction and pours water underneath machine on the floor. This all happens while i am using the hand attachment tool, but also occurs when i tried just the machine is running..what am i doing wrong. it is new..only used once about 6 months ago


Press the handle release kick-button with your foot, extend the handle all of the way back, and take a look at the gap between the base of the unit and the handle/reseviour assembly. You should see several black hoses attached to the base and running ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

A friend who bought a multimaster less than a year ago has had his start a loud 'clattering', dry, noise, and the gearbox started to get hot. The output shaft now has about the same amount of slop as the total movement should be. It is one of the quick attach type. I bought one of the allen key attach type, and have found in the past with various 'name brand' tools, drills, angle grinders etc that they usually use a 'dry' type grease which soon throws off the necessary parts and they run dry u


Fein is an excellent tool and has an excellent warranty that will be void the moment you open the gearbox. I do not recommend this action. Fein is quick and responsive, especially for a less than one year issue.\015\012Farmerbear at FixYa.com ... Fein Multimaster Rs - Msxe 636 - 2 Rs

Suction using dyson normally is fine,but when using tools its as if the suction has reversed and there is no suction for the tools


... Dyson Vacuums

I have a Bissell 9500 proheat 2X cleanshot w/dry Aire it works great on cleaning carpets. When I try to use the tools it will spray but will not suction. How can I get the suction to work when using the tools?


Ensure the handle is in the upright position and the selector is on tools,Please take the time to give this solution a fix ya ratingclarkco ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Smells hot My Eureka Atlantis has been used for only my home cleaning use and today i went to use it and it is NOT suctioning like it should and it smells very hot and need assistance.


Sounds like you may have a bad motor. It is probably trying to work, that is why the suction is low and it gets warm. It will have to be replaced. ... Eureka Atlantis 2591A Upright Steam Vacuum

When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond


Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis


U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

No suction whether I'm using the tools or using the vacuum upright, there is no suction. I have checked the hose to make it is not clogged- still no suction. What is the problem?


Your intake hose might be clogged at the bottom ,it the clear hose that comes up from the bottom .you will see it from the back.take the dirt cup off there is a filter inside that most likely is clogged ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I don't have any suction when i use the vacuum, if i use the tools adaptor i still have suction. how do i get the suction back to the vacuum?


Plugged lower,, hair,, carpet etc. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Power floor tool on DC21 keeps shutting off when in use. Must keep hitting start button on tool while using


... Dyson DC21 All Floors Stowaway HEPA Bagless Canister Vacuum - Iron/Titanium/Yellow

Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.


It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

My upright kenmore progressive vacuum will not suction up when using the sweeper. It will suction things when I use one of the tools. I have put in a new bag and have tried to see if anything is blocking the bottom. It sometimes makes a very loud noise when I try to vacuum. If I press the intell clean on and off yellow button the noise may go away but it still does not work.


Double check hose placement, making sure you have the hose inserted into the correct slot. The long attachment nozzle stores in the front hole on the right, and the sucking hose inserts into the rear hole on the right. I know this is too simple of a ... Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.


... Hoover Vacuums

No suction my riccar 8850 has no suction. I cant find any clogs and there is some suction on the hose when using cleaning tools but when hooked up to the vaccum bag it wont clean


Replace your belt. Remove the baseplate, remove the brushroll, place a new belt around the motor pulley, then around the pulley on the brushroll, and pull the brushroll back into place in the nozzle. Spin it by hand to make sure it spins, (otherwise ... Riccar 8850 Vacuum

Dyson animal D28 suction on floor vacuum mode is so strong I can't push the machine. Last used for hand tools, is there some mechanism that is stuck?


... Vacuums

How to turn on to use crevice tools


... Hoover F5906-900 Upright Steam Vacuum

Runs for a few minutes. Loses suction the shuts


It sounds like it's draging on the motor Also heating up the thermister switch. I would recomend having this look at from a vacuum repair shop ask for free estimates if you call around. save some $$$ ... Royal RY9200 Bagged Upright Vacuum

Dyson DC07 shuts down after 5-10 minutes of use and horrible suction!


I have had this problem on two dysons and have solved it by replacing the so called lifetime pre-filter. The problem is not the washable blue sponge but the material gauze filter in the plastic surround. \015\012\015\012To see if this i ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Motor dying? recently my herritage has been sounding sick, i tried to use it the other morning and it barely could blow up the bag, there is also a hot smell to it when it is running, the motor doesnt sound as powerful as it use to. Any suggestions?


Replace the carbon brushes in the motor. ... Kirby Heritage II Vacuum

Loss of suction when using upright. Suction remains for samll tools


Over 21 years repairing vacuum cleaners, I have removed yards of duct tape,surgical tape and package tape from hoses.wands and cords. I have found the best repair method for torn hoses is a product called "Stretch and Seal". This is a silicone-based ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0644 seconds