Having problems with your GE Vacuums ?

Suction stopped working immediately

\015 My vacuum is not suctioning at all. it was working last week. it just leaves stripes on the floor. it's bagless but the dist compartment is clean and the floor brush is also clean. in fact, when turned upside down, it almost seems as if it is slightly blowing out instead.\015

Answers :

There is a hose on the unit. Disconnect it at both ends. Stretch it out. Look down it. If you can't see down it, rod it out.
Repair Help & Product Troubleshooting for GE Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Suction stopped working immediately

There is a hose on the unit. Disconnect it at both ends. Stretch it out. Look down it. If you can't see down it, rod it out. ... GE Vacuums

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!

Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

Base suction and tool suction both have stopped working

On the top of the water reservoir (under the handle that you use to lift it off) is a large dial. The top says "hose" and the bottom says "floor". Turn it to where it says floor. If your brush is not working than you going to have to tak ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The floor head is no longer working. The canister works, there is suction, but the floor head is dead. No lights, suction control switch inoperable, no headlight, nothing. It just stopped one day during a vacuum session. Thanks.

Hi poohbear4760...\012Check your wiring going to the vacuum head, some vacuums have a problem with corrosion on the plugs...take your connections loose and lightly sand with fine grit sandpaper the metal ends.\012Plug the wires back toge ... Vacuums

My Bissell 9500's base suction stopped working, however the hand tool suction works.

I can tell you how, but I think if you look at this manual it will show you how to fix your problems...go here to download: http://www.bissell.com/images/UserGuides/9500_908.pdf ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All

Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Hand held vacum suction stopped after 1st use. Was working fine, suction does work if onfloor but won't once turned to tool

Go to the web page and see instructional video and maintenance helphttp://www.bissell.com/how-to-videos/God bless you ... Bissell 2X Proheat 9200 rug cleaner

I have a dyson animal dc24. It is 7 months old and has stopped working. The hand tool is working fine but when I insert it to engage in normal vaccuming the suction stops. I can hear a strange air sound. Also the brush is spinning but it is not picking up. I have taken it apart and checked for a clog but I don't see one. Any advice?

Hi there,I'm sorry to hear your DC24 Animal isn't picking up as well as usual. Although I note you've already checked for blockages, it sounds as though this is likely to be the cause of the issue.To locate and remove any blockages, p ... Vacuums

Dyson dc41 floor suction stopped working

... Dyson Bagless Upright Vacuum DC41 Animal

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks

This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!

Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current

I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

Machine turns on, has little suction, then stops working.

It would be helpful to know what model of vacuum cleaner you're talking about. Basically though, your machine has a blockage somewhere (hence very low suction), and is cutting out after just a few minutes because of overheating.  You need to exp ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Suction stopped working

... Miele S514 Solaris Electro Plus Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!

Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

ProForce 1500 has suction but the brush roll motor stops working.

... Proteam ProForce 1500 Bagged Upright Vacuum

Suction Problem I just borrowed the Hoover Steam Vac Deluxe w/ 5 brush agitator from my neighbor and it worked ok for the first few minutes, although the suction would stop and go. When I had enough water to dump I did it and when I put it back on it no longer sucked the water up from the carpet. She admits to having it for 15 years, but why did it have to break on me. Makes me look as though I did it!

Check and make sure the dirt water tank is properly on if it it is chech inside the lide to make sure the red stopper is not stuck to the top this will cut off the suction ... Hoover F7431-900 SteamVac Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.

Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum

Hello, my Kenmore 27514 canister vacuum only works on the hard floor...the carpet suction stopped working while I was using it. Is there anything I can do to fix it or is it necessary to take it in for repair? The vacuum is only 1.5 years old. Thanks. Susan 702.340.8015

You need to replace the belt that drives the beater bar. You can do this yourself very easily. If you need help, let me knowJim ... Kenmore 27514 Bagged Canister Vacuum

We have a 25512/13 and suddendly the powermate is not pulling forward and sucking. We checked the belt and it is ok. The light stopped working when it stopped thrusting forward. When we remoe the powermate, it seems that there is still suction. Can you help us?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

The suction on my eureka optima stopped working but the roller still works, what might i do to fix it?

Hi there. Most suction problems are due to a blockage. Start with the base and look carefully for debris that is stopping air flow. You may have to remove the base plate to get to the problem. I am including a link to the manual for your machine. ... Eureka 431A Optima Bagless Upright Vacuum

My dyson DC04 started to **** a dog toy up the main bit with the brushes - stopped it immediately and removed the toy but since then the suction is still ok/strong with the extension hose picking up but no suction is getting to main scetion/brush area - sounds like a pipe is disconnected from the front area - nothing obvious on the surface....HELP! Thanks in anticipation........... Julie Price

Get a different brand vacuum. Dyson's are easily the worst vacuum I've ever owned. I've tried the DC14, DC25 and DC33 they are all heavy plastic POS's made in Malaysia. I've owned every kind of vacuum under the sun. Rainbow, Kirby, Oreck, Riccar, Seb ... Vacuums

My Bissell Proheat has stopped suctioning the water solution. It has worked well in the past, but the last time I used it the recovery bladder had just a small amount in it. Could it be stopped up?

I have this machine too. IF the soap dispenser does not have anything (even water) in it the water sprayer will not spray. Sometimes the water valve from the tank has an air bubble in it. Remove the tank and push up the valve. A little water will fal ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0527 seconds