Having problems with your GE Vacuums ?

This ge model aew10ajs1 keeps shuting off an doing its owen thing i checked for loose wires an the outlet is good the coil is a little dirty but not bad

Answers :

The motor may be overheating due to a clogged filter. there are temperature switches in them that are safety switches in them to keep them from catching fire.
Repair Help & Product Troubleshooting for GE Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

This ge model aew10ajs1 keeps shuting off an doing its owen thing i checked for loose wires an the outlet is good the coil is a little dirty but not bad

The motor may be overheating due to a clogged filter. there are temperature switches in them that are safety switches in them to keep them from catching fire. ... GE Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.

... Kenmore Vacuums

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.

I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.

If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

Help ok the diagram is helpful but i have a black wire that came loose from somewhere it has a little prong on it does it click back in opposite from the white let me know please

I am not sure what exactly you are referring to but I think that it may be a motor lead. See pictures below (shown is white but second wire to the motor is black) ... Rainbow E series Canister Wet/Dry Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


I have a 6550 that just stopped working. I had the on/off switch tested to find out that it was dead. I replaced it and still the machine does not work. Could the wiring in the handle be bad? How do you test if the motor is still good?

I test a motor by taking an old vacuum cleaner cord with alligator clips on the ends and hook it up to the motor simply bypassing the entire vacuum cleaner. If it runs then I know the problem is not the motor. ... Simplicity Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?

Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t

... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Does not pick up, no vaccum, motor runs, no blockage, should feel suction on hose outlet without hose hook up. Paper filter missing over cloth filter. float overload ball free, seal on section good no leakage. Maybe bad motor but runs.

Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Minuteman C82906-01 HEPA Vacuum Vacuum

My aerus 9000 series vaccum has no power at all... all wiring is good, I believe there is a bad circut board where there is a relay on it.. any suggestions

Sorry to read about your problem, I hope this helps you out.no ckt board.. bad power switch or defective motorI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Vacuums

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?

You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help

Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Loose wire Been tugged causing loose wire at handle end of flex

Needs new cable 20.00 for replacement 0800 294 4692 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My plunger (bought in Chile) has 1. a metal filter, 2. a convex (not flat) metal disc with central hole for rod, 3.a metal disc with holes of two different sizes in circles radiating from the centre 4. plunger rod with screw and 5. a spirally coiled wire forming a circle. I cannot figure how to fit these especially the coiled wire. Help appreciated. Thanks

Place the coil in the hole and turn untill reach the desired height. ... Vacuums

Picked the zig cp3g at car boot sale,just what i was looking for,but no instructions just wires been cut,tidy little unit.on the battery transfer switch, red, green and blue. and from lights green,aux brown,and water pump yellow.....firstly how do i wire to power up,and how does the single wires from unit not have return wires,thanks.

Hi,\015\012\015\012For your requirement wiring will be following: the green wire will be from the knob beside\015\012the tree switch to battery switch. Red wire will be from another side of battery\015\012switch to circuit o ... Vacuums

I had a loose wire in my Oreck XL motor. I took it

Lights are 12 volts.\015\012\015\012The motor has taps on it to pull 12 volts rather than 120 volts for the lights, uses the motor as a transformer.\015\012\015\012Should be black and white to the motor from the switch, believ ... Oreck XL Ultra Bagged Upright Vacuum

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks

CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

I also have the Whirlpool Accudry Gold AD70USV 70 Pint Per Day model. It works fine in every way except it SMELLS BAD. How FRUSTRATING. Smells so bad, we don't want to use it, but paid good money for it, and too much hassle to go back to manufacturer and seller. It did this since day 1, but we kept thinking it would clear up and let it go too long. It STINKS.

Try cleaning roller brush and the and all the plastic around it... if it is a dust cup then clean it real good also... ... Vacuums

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug

... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Can you send me a La Cimbali M22 Premium espresso machine power switch wiring diagram? I have a machine without a power switch. The switch is on order but I still have to connect the 10 loose wires. Thanks, Terry...

... Vacuums

I have an electolux [ lux classic] vacuum cleaner, and there is no power to it. I think it is a loose wire, as it was tempermental before. I can't find a way to get into it to see if it is a wire

Does the green power light located on the top of the vac come on with the cord plugged in the outlet ? If so your switch could be bad. If not, you could have a bad connection or a broken wire. Caution ! If you do get into the vac, you can cause more ... Electrolux Vacuums

When running the 2100 Electrolux vacuum, it is stopping and starting when pulling or pushing the floor attachment. Seems like the connection at the top of the handle is a little loose or the electric tabs are loose where the hose connects. Any ideas?

Other option is that on the hose end of the electrical connection, you can use an awl on the electrical connections to bend them in slightly so they make good contact when they are automatically plugged in when you connect the wands. HOWEVER, ONLY D ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Hoover wiring the blue wire that is in the lead that runs from the hoover to the plug that goes in the wall has come loose at the hoover end and has come out of the actual hoover. i've unscrewed it but am unsure as to where the blue lead (bare copper) needs to be screwed... if you see what i mean?!!

Hello lukeplayer,\015\012Based on your description, ( first disconnect the plug from the wall recptacle).You will need to open up the Hoover Vacuum Body to gaion access to the internal wiring. In order to better assist you, please provide me wi ... Hoover Vacuums

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds