Having problems with your Halo UVST Bagged Upright Vacuum ?

Halo vacuum uv-st3290 the brush won't turn - Halo UVST Bagged Upright Vacuum


Answers :

Repair Help & Product Troubleshooting for Halo UVST Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Halo vacuum uv-st3290 the brush won't turn - Halo UVST Bagged Upright Vacuum


... Halo UVST Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Windtunnel vacuum brush won't turn - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Why won't my vacuum turn on? - Fuller Brush FBHD1 Bagged Upright Vacuum


... Fuller Brush FBHD1 Bagged Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Brush won't turn vs14 windsor versamatic - Windsor VS14 Versamatic Bagged Upright Vacuum


... Windsor VS14 Versamatic Bagged Upright Vacuum

Brush motor does not turn on - Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum


You could check Sears.com and click on parts then type in Model # or Part # this will get you a parts list you can choose from. ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

Brush does not turn because belt is loose - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


You need a new belt that isn't stretched. You can get a replacement here:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brush won't turn 0n the 380 lindhaus - Lindhaus 380 Diamante Bagged Upright Vacuum


... Lindhaus 380 Diamante Bagged Upright Vacuum

Dyson dc33 bagless roller brush won't turn - Dyson DC33 Bagged Upright Vacuum


... Dyson DC33 Bagged Upright Vacuum

Dyson dc33 brush bar won't turn - Dyson DC33 Bagged Upright Vacuum


... Dyson DC33 Bagged Upright Vacuum

Floor brush won't turn. - Clarke CombiVac 12 Bagged Upright Vacuum


If yours is a dual motor unit a microswitch in the base of the vac powers the brush roller, additionally the carbon brushes may need replacement..far cheeper than a motor.or your belt may be stripped or streched due to string or hair binding th ... Clarke CombiVac 12 Bagged Upright Vacuum

The brush isn't turning on my Kenmore progressive upright bagged vacuum model 116. The serial number is M80261402.


Replace the belt ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

Brush turn in hose mode - Eureka Smartvac 4870 Bagged Upright Vacuum


Please go to : http://www.eureka.com/en-US/Customer-Service/Videos/see the video and troubleshooting guide with common sense,for repair.this problem normally come : a) belt is broken or worn, need replace b)brushroller blockage, clean ... Eureka Smartvac 4870 Bagged Upright Vacuum

The brush on my dyson dc 33 is not turning - Dyson DC33 Bagged Upright Vacuum


Hi there,I'm sorry to hear you're having difficulties with your DC33. If the brushbar doesn't seem to be rotating, please follow the steps shown in our online support guide to check everything is correct with the machine: ... Dyson DC33 Bagged Upright Vacuum

Brush wont turn u6485900 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Here is manual > http://hoover.com/file/509/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brush won't turn. - Kirby G4 Bagged Upright Vacuum


Are you certain the belt attached as it ws suppose to when you locked the front onto the base? ... Kirby G4 Bagged Upright Vacuum

Hoover carpet scrubber brushes wont turn - Hoover U6434-900 Bagged Upright Vacuum


... Hoover U6434-900 Bagged Upright Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Panasonic upright vacuum brushes dont turn - Panasonic Bagless Upright Vacuum Cleaner MCUL915


This may be too obvious, but do you have the Carpet switch turned on (bottom left of vac). Agitator brush does not go around if Floor/Tools is switched on, ... Panasonic Bagless Upright Vacuum Cleaner MCUL915

When I flip the switch on my sebo x1 upright, a red light comes to the brush and bag icons. However, I cleaned out the hose and checked to make sure there is no obstruction from the brush to the hose also, or from the hose to the bag. It is clear that juice is coming to the vacuum, but there is no sign of life except the two red lights.


Thanks for contacting fixya. You should pull out the bag and reset the machine. You should take all the user replaceable items. And turn it on. You will get lot of errors. Then turn the machine off. Put back all the accessor ... Sebo Automatic X1 Bagged Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

Kenmore vacuum upright no brush turn


... Kenmore 34923 / 34925 Progressive Bagged Upright Vacuum

Eureka IMA Vacuum - brush not turning - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Your belt is probably stretched or broken. Here is a link to the belts you need and to the manual which has instructions:Eureka Altima Replacement Belts ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1438 seconds