Having problems with your Hansgrohe HG-T201 S Shower Faucet with Thermostatic Trim, Volume Contr ?

HG-T201 control weight goes down

\015 Handle too heavy = turns off from hot to cold\015

Answers :

Repair Help & Product Troubleshooting for Hansgrohe HG-T201 S Shower Faucet with Thermostatic Trim, Volume Contr

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The one of the controllers for the electric blanket keeps flashing an "e". The other controller is fine. We switched controllers and the same thing happened. We have unplugged the blanket for several minutes and turned off the controller for several minutes. It always goes back to displaying the "e". It is a warmspun blanket and I cannot find any information on the company so that I can contact them to see about the 5 year warranty.

I did some searching-- and I came up with this Linkedin page-- seems to have some information-- Let me know if it helped-http://www.linkedin.com/companies/jla-homeMack B ... Vacuums

I bought a house that has a 1970s GE microwave oven that's built-in above a traditional oven. (Unfortunately, I can't locate a model number for the microwave.) I'd appreciate having information about the "food temp control," which is on the front of the oven. There is a wire probe that goes from the inside of the microwave to the food. I assume that relates to the "food temp control." I'd appreciate having any information about how to use the "food temp control." Also, I 'd like to know wh

I serious doubt that probe would work any longer for they go out in ten tears or less ... Vacuums

I have an older Bernina 830 Record sewing machine and I've noticed that it makes a growling noise when I first step on the foot control with the machine in the low speed setting. The noise goes away when the speed picks up. Is this serious? What's the fix?

... Vacuums

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]

Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum

I have a Sleepwell Dreamland Luxury cotton Electric Duvet. It has twin heater controls, the control has a 1 to 9 heat setting and also a time duration function. One of the controlers works fine but the other turns itself off after about half an hour. Can you help and perhaps give me an address where I might purchase a new heat control.

... Vacuums

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz

Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum

Im trying to put the peice back together that goes under the tube that hold the water the part that goes into the hole in the vacum.. i took it apart because its not spraing right to see if it was cloged.. and now im not sure how it goes back together.. can you please help me.....

I tried to find a service manual for this, but came up with only a exploded view diagram:\015\012\015\012http://ineedbags.com/images/b8920.jpg\015\0 ... Bissell 8920 ProHeat 2XTM Upright Vacuum

Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900

Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?

Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

One of my Imetec electric blanket controller is faulty. I swopped the controllers and the fault follows the controller. Can I get one somewhere. The guarantee has expired.

... Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

My danby kegerator model DKC645BLS controller circuit board corroded and no power to the compressor,I already have an external temperature controller,can I just bypass the controller and circuit board

... Vacuums

Vacuum cleaner We have a panasonic MC-E47electronic which seems dead. It has a speed control which we nearly always had on full anyway. Have tested continuity through plug, flex and on/off switch and all OK. from then is open circuit through speed control which consist of slide rheostat and mystery small green box (2cm x 2cm x 1cm approx). Across motor there is negligable resistance. Machine is quite old and not worth paying out loads on poarts if it is safe to bypass speed control and connect

Yes it is safe, but i would make a switch? ... Vacuums

While replacing my power cord on my DC25 a spring popped out I have no idea where it goes. I need a diagram so I can see where it goes

Here is how the switch assembly should go together: ... Dyson DC25 All Floors Bagless Upright Vacuum


Hi,i think the problem is with the needle bar,the alighnment has been distorted internally,i think you should re-align the needle bar in order to restore your machine back to a normal working condition.\015\012\015\012\015\012Thanks and t ... Vacuums

Vetus bcc 1000 inverter/charger When this unit is started it goes into overloadthe battery bank is new and we have isolated it from the narrow boat electics and pluged in a fan heater but still it goes into overload.

... Vacuums

I inherited a Simplicity 4380ED serger. It won't cut the fabric. I changed the lower blade for a sharper one. It is lying level with the throat plate. The upper blade is smooth. The fabric edge goes along the upper cutter and rolls over from the top and goes through the serge stitching.. No cut.

A tech on this site wrote this, when a similar model as yours was "mangling the fabric":\015\012Best Solution\015\012posted on Jul 07, 2009\015\012\015\012\015\012 \015\012\015\012 ... Vacuums

My roomba mounts up to the charger the light blinks red then after a time it goes green but when I dismount it and push the green button it immediately goes red. It doesn't beep or do anything. It is that the battery is not charging?

You have dead nimh (nickle metal hydride) batteries. You\012will need a replacement. You can test for this by removing the battery\012and holding the power button for 15 seconds. This will restart the\012charging cycle as if the battery were new. ... iRobot Roomba 560 Robotic Vacuum

I have a Hampton Bay Midili fan which I just installed about a month ago and it was working fine. A few days ago when I flipped the switch on the light flickered on and off consistently until I turned the switch off. The remote also stopped working to control the fan and light. Since this model only can be controlled by the remote I am worried I will have to replace the remote already after only 1 month!

In many of these remote controlled lamps you cant use the new spiral light bulbs .. you can only use standard incandescent lights .. if thats not the trouble then you may indeed have a bad controller (in the fan) .. there is probably at least a 90 d ... Vacuums

The digital readout on my Redmon brand digital small animal pet scale will not "zero out." When turned on, the weight displays a weight from the memory, which is what the scale should do, but it's then supposed to zero out so you can weigh the animal. I've put new batteries in, and also taken them for a while (up to an hour), then replaced the batteries, and turned the scale on. This has not worked. Any ideas?

... Vacuums

U-Shaped piece I was in the hospital for a couple of nights and my 80 year old mother decided to go to my house and vacuum my house. When I went to get it out to vacuum the other night the u shaped part fell off. I guess my mom had somehow knocked it off. Now I cannot figure out where it goes. It is a plastic U-shaped piece. Can you help me? I sat for a hour trying to figure out where it goes.

It attaches at the bottom of the hose and goes into the bottom of the valve. Located on the back bottom of the unit. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Where does it go and how do I replace the belt on a Deluxe Hoover Mach 3.8 bagged windtunnel action vacuum? I kno it goes somewhere around the brush but it fell off when opened and I can't tell where it goes. I have a replacement belt

... Hoover Vacuums


What kind of vacuum is it ? call me at 314-628-9153 and i will walk you through it ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0160 seconds