Having problems with your Hayden Industries SuperVac 6000 Central System Vacuum ?

The brush on my hayden 6000 supervac is not rotating when power is on and i can't figure out how to open the vac to get to the belt. help please

Answers :

First you will want to remove the light cover. this can be done by pusing as you look at the front of the powerbrush on both the left and right side of the head.
There you will find the lightbulb and 2 screws to remove. Remove both of the screws and turn over to pry with a screwdriver at both the sides of the powerbrush to remove the top cover.
\012Once you have the lens cover off you will also see in the plastic the belt change instructions.
\012When you want to put the top cover back on, it will act much like a hinge, hook it on to the front of the head where the brush is, and snap it back into place at the back.
Repair Help & Product Troubleshooting for Hayden Industries SuperVac 6000 Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush on my hayden 6000 supervac is not rotating when power is on and i can't figure out how to open the vac to get to the belt. help please

First you will want to remove the light cover. this can be done by pusing as you look at the front of the powerbrush on both the left and right side of the head. There you will find the lightbulb and 2 screws to remove. Remove both of the screw ... Hayden Industries SuperVac 6000 Central System Vacuum

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks

Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

Kirby belt my belt on my kirby ultimate g came off and I can't figure out how to get it back on please help!

Check out my online guide. I also have instruction manuals!\015\012\015\012http://reviews.e ... Kirby Ultimate G Bagged Upright Vacuum

I'm trying to change the filter....One person told me to open the hose end and take the bag out and go from there, but that isn't the right way!!! It's the other end where a couple brushes are able to be stored on top of the canister, but I can't figure out how to get that section off..it's as tight as a drum HELP PLEASE and thanks. Betty

There's a tab at the middle of the lower back of the tool holder (air diffuser). Pressing in on that tab should enable you to lift the back of the holder first, then lift off the whole thing. It will come off, just make sure the tab is in far enoug ... Electrolux Epic 6500 Vacuum

I have a dyson DC14. the forward lock came out and I cant figure out how to get it back in. Please help!

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I had to take apart hand tool for steam vac and now I cant get it back together. Please help.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.

Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!

First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Help!!!! i have an older model of the dirt devil bagless quick vac. and it has been working great, just last week i was vaccuming my bedroom and i accidentally sucked up a string belt that goes with one of my capris. and today i emtpied out the dirt cup but it seems the the string belt that was sucked up is not within my reach and whenever i start the vaccum i get this distinctive noise that i've never heard before. help.

It's likely wrapped around the brush\015\012pull out the roller and un tangle it ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help

You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

I have a Dirt Devil Swivel Glide Vac with a broken belt. I have purchased the correct belt(#4).The bottom is off and I cannot tell where the belt connects to. Please help. Jann

It connects to the left side with the little metal rod sticking out.then connect to the wooden roller. in the space without the brush on it. roll the wooden piece to check if everything moves. then put back together. ... Dirt Devil Vacuums

There seems to be a wheel that holds tension to the belt which came off. Now the belt spins and makes a grinding noise. I cant figure out how to get to the belt? Any one have advice?

I can help you a lot further if you can send me a picture of the bottom side of the vacuum. My email is [email protected] Once I see a picture this will help me tell you how to fix it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Turbine Hi I found out through your site that my turbin is bad on my steam vac and I found some information as well on how to disasemble the steam vac to get to the turbine but still was wondering if there were some more detailed instructions on how to remove the turbin. I am a sigle mom and doing the work on the steam vac myself and need a little more detailed instructions. Please help asap and have a bless day.

There are some screws on the bottom that have to come out so you can remove the top housing. Take the brush block out, there are 2 screws above where it sits. The turbine sits near the front, and in the mid section, 2 screws on the front of it and 2 ... Hoover F7220900 SteamVac V2 Upright Vacuum

I am smelling a faint burning rubber smell and I think the belt needs changing, but I can't figure out how to open the case to change the belt. Can you help me?

... Hoover U5068-900 Sprint Upright Vacuum

My mother's Hoover Widepath is making a funny noise. I wanted to get into the area where the brush and belt are and couldn't get access. Please help!

Please see if there are four screws, located at the corners of the brushroll opening, underneath the cleaner. Remove these screws, then remove the bottom plate. ... Hoover U5258-900 WidePath Bagged Upright Vacuum

Clogged hose I just accidently sucked up a sock and now I have no suction. I have no idea how to get the handle off and doubt this would help anyway. It is an Electrolux central vac. Help please!!!

If you have a drain auger then you can stick it in until it won' go any further then you have hit the sock.turn the cable and grab the sock and pull it to the surface.please leave feedback ... Electrolux Central Vacuum

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!

... Hoover Vacuums

I have a Eureka Altima vacuum. The model number is 2996. I don't think my vacumm is sucking any dust. Plus, it smells like a burning leather. What should I do? I have tried to get help from others and they tell me that I should change the belt. But, I don't know where it is. Please help.

Sounds like the belt for sure. Here is a link with the owners manual. It shows how to get to and change the belt. http://www.eureka.com/index.php?option=com_productdisplay&view=productdisplay&task=getproducts&productid=2&produ ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a broan central vac system need belt for cv315-b vac head cant seem to find one any idea where i can get 1 thanks

I believe that the Broan replacement part number for the belt for the CV-315 power head is a 9967-0585. available through a Broan/Nutone dealer. ... Vacuums

Houver Cleaner My self propelled windtunell baged Vacumn has a broken belt. The small visible one that is visible is intact. This is the thick belt. I cannot for the life of me figure out what to open and how to replace it. The model # is U6 401-9RM I keep asking for a manual online but it doesn't recognize this number. I am 67 yrs old broke and fix it challenged..lol can you help me?

Take off the bottom plate, The flat belt ges around the motor shaft and then around the bigger pulley by the V belt. It will stretch to o on.\015\012\015\012 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt?! hello, I need to change the Eureka Oxygen Canister Air Driven Upholstery Tool's Belt (model 5860Avh), but I don't know which one to get? any help please? Best, Pierre.

You will probably have to order it online. ... Vacuums

Need to change belt on hoover upright model u5093-900, but can't figure out how to open it up to get at the belt.

... Hoover Vacuums

Belt broke I need to find out how to get in the vacuum to replace the belt but cannot figure it out. I do not have the owners manual for this Eurka The Boss Superlit bagless (402a) please e-mail me any directions if you know how to do it,thanks. [email protected]

How do i change the belt on my eureka the boss lite vacum ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1071 seconds