Having problems with your Hayden Industries Vacuums ?

Hayden 3600 the motor is pulsing off and on at about 1 second intervals


Answers :

Repair Help & Product Troubleshooting for Hayden Industries Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hayden 3600 the motor is pulsing off and on at about 1 second intervals


... Hayden Industries Vacuums

Hayden Premier Motor Pulses


There are several possibilities here, its possible the low voltage relay is bad, possible that the carbons on your motor are worn, or may even be a thermal sensor in your unit shutting it down, ive even seen improper assembly of motor which cause wir ... Hayden Industries SuperVac 6000 Central System Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on


... Miele Blue Moon Bagged Canister Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Motor My vacuum cut out as I was using it. After some experimenting I found that the circuit reset had gone off. When I tried a second time while near the motor , there was a flash and again the motor shut off. At this time I am guessing that the motor is faulty. The central vacuuming is approximately 12 years old.


If it tripped the reset again, I would probably agree with you. Check out centralvacuum.com for another motor. They aren't the cheapest, but they have excellent support. Good Luck!! ... Easy Flo EF1400 Central System Vacuum

The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.


This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums

I have a karcher 350 water blaster that has suddenly lost water pressure. the motor still works but no pressure. If i give it 10 or more seconds it builds up a bit of pressure but when i pull the trigger the high pressure only lasts for a 1/2 second blast then just normal tap pressure. Can anyone offer advice . thanks


... Vacuums

No motor when switched on two red lights flash,cleaned hoover, put back together motor started,then cut out after a few seconds


I would double check your wiring, Make sure all wiring is tight. No cracks, no pinched wires. If needed, bypass the switch and see if it will stay running. If so, switch would be bad. If it's the same, then you have a wiring problem or a worn motor a ... Sebo Automatic X1 Bagged Upright Vacuum

The Oreck vacuum motor sparks the stop running. Plugged to another outlet, the motor did the same things, run for few seconds with sparks and stopped again.


... Oreck XL2200 Bagged Upright Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.


Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

THE SECOND LIGHT ON AND MOTOR STOP AFTER FEW SECOND.


Depending on when you got your vacuum, it may still be under warranty. I strongly suggest calling your dealer or sales rep, or taking the machine in, to have them check it.\015\012It may be something as simple as a full bag! ... Electrolux Epic 6500 Vacuum

Dyson My Dyson DC04 runs for a second or two then stops. I have checked the motor. The brushes are good but the commutator is a slightly pitted.Do I need a new motor?


Hi.\015\012\015\012Check mains lead where it enters machine very common for internal fracture.\015\012\015\012To prove this try waggling lead with machine switched on if it starts & stops this is the fault.\015\012 ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Hi. DC14 not running. Repeated pressing of the switch occasionally produces a split second whirr from the motor. I had been picking up plaster dust for some time but stopping regularly to clear out filters and 'the little tubes.' The switch is fine. I cannot see how to get at the motor. Thanks , Chris


Hi again. I finally figured out access to the motor. One of the brushes was burnt and broken. I have ordered a replacement set and cleaned up the comutator ( spelling ?). Thanks, Chris ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell 9500 proheat 2x deep clean. It only squirts for a couple of seconds and stops. I turn the machine off than on again does the same thing again. If it the pumpt motor, I need to know which is the pump motor.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Motor is pulsing on and off, suction is good when motor running


... Broan-NuTone CV653 Bagged Central System Vacuum

I have a TriStar LEC vacuum and today I turned it on and for a split second the motor whirred and then nothing. Now it won't come on at all. I cannot find any way to access the motor.


How do i replace the power cord on my lec tristar vaccum? ... Tristar Vacuums

The motorized wand attachment keeps shutting down after 10 to 15 seconds after pushing the red reset button. I've thoroughly cleaned dirt/debris from around motor. Do I need a new reset switch? Thanks, Tom


Either the reset is bad or the motor is drawing too many amps and tripping the reset. Do you have an amp meter? Check the amps being pulled by the wand attatchment against the load recommended by the manufature, this is usually located on a plate som ... Rainbow E series Canister Wet/Dry Vacuum

Hayden Vac2400 my hayden 2400 does not have any suction and it smells like something is burning, is it the motor?


Check the carbon brushes, they maybe worn out and need replacing. ... Hayden Industries SuperVac 2400 Central System Vacuum

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.


It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

Not working  I hit the switch and there is no sound of a motor.  Nothing is happening.  It was working seconds earlier and suddenly it stopped.  The plug was in and I replugged it into the outlet.  Still, no power and no motor sound. Does this happen if the belt goes? Thank you, Jill


If it was just a broken belt you would still hear the motor running. most likely its in your cord or switch. check the main cord, connections to the switch, and also the motor supply cord that goes from the handle to the vacuum head. ... Oreck XL Ultra Bagged Upright Vacuum

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.


... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

Dc35 pulsing Hi I have a DC35 it works fine until i put the main head on and then the motor starts pulsing and cuts out after about 10 secs. If i remove the main brush head it runs fine again ? Please HELP :)


Check for debris in the head and remove ... Dyson DC35 Handheld Vacuum

I have a mile tt2000 that works fine up to 1300W but if I crank it up higher the motor decreases and increases speed every couple of seconds. I have changed the bag and filters and done the usual cheCks for blockages but can find nothing amiss. Unusually when it is running and I block the intake it will run at full power but as soon as I clear it the motor "hunts" again. Any ideas.


... Miele Cat & Dog 326i Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0372 seconds