Having problems with your Henry Numatic "" Canister Vacuum ?

My henry vac switch is dead.

\015 When I switched on my vac today it wouldn't work. Not even a slight start up of sound. I tried the plug in another mains socket and the same thing happened.\015

Answers :

You will need to remove the top cover of the vaccum by removing the 4 screws underneath.The you need to test with a multimeter if you have 240 volt power to the bottom of the switch. If you haven,t power there you will need to check the plug connection or replace the power lead.
Repair Help & Product Troubleshooting for Henry Numatic "" Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My henry vac switch is dead.


You will need to remove the top cover of the vaccum by removing the 4 screws underneath.The you need to test with a multimeter if you have 240 volt power to the bottom of the switch. If you haven,t power there you will need to check the plug connecti ... Henry Numatic "" Canister Vacuum

I have use my henry with no problem, tunred it off with the red switch on the top, 20 minutes later I went to use again but the machoine was toatlly dead with no power I have changed the plug fuse


Could be fault @ plug.. try cutting off 10 mm of cable then redo plug ..Replace fuse then try, if still dead try switch, you could short this out or if you have multimeter check for contact...if stii no action could be motor.... ... Vacuums

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot


It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

On off switch stopped working 3rd one to do so this one cannot be returned to old ? model QPV10.5b nothing on shop vac site and nothing comes up on Digi-key site really do not want to buy 150.00 vac again but cannot find on off switch! thanks for your help


Use a higher amp rated switch. If this is not available, then solder and insulate the wires where switch should be, then install an aftermarket in-line switch. ... Vacuums

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the


Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

My Shop Vac 90L600A is getting electric thru the cord and into the switch, but it doesn't switch on when you toggle the switch from off to on. Is it a bad switch?


Check the othere end of the switch. You may have a brushes problem in the motor. You will have to check the switch while hot - be careful ... Vacuums

When i switch my henry hoover on it works fine for exactly 50 seconds then switches of for approx same time then comes alive again for 50 secs and so on...driving me nuts.


... Vacuums

Replace on/off switch on rainbow D3 vacuum - Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch


... Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch

Need switch for QPV 11.5 shop vac - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???


Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

Need shop vac switch for J150A - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Henry will switch on and stay on, only while the switch is pressed.rnHow can you get at the switch to replace it? There seem to be many crosshead screws under the motor part,- which need to be undone? Thank you.


Sweeper shop to get switch, you could have a wiring problem . Take casing off and check out and get those screws out of there they could cause some damage all while unplugged of course.bare wire coud cause your problem and thoe screws hopefully arent ... Numatic Henry Bagged Canister Vacuum

My Sanitaire Commercial vacuum SC5815 A-2 does not turn on. It is quite new and seems to be "totally dead." Serial number: 0632005978 It is firmly plugged in, I have tried numerous electrical outlets, and I have tried the on-off switch numerous times. I wonder if there is a simple circuit breaker switch somewhere on the vacuum that I could switch without going to a repair shop? Or, I wonder if some latch is loose that shuts off the current, but I have checked the latches and they are clo


... Electrolux Sanitaire True HEPA Upright Commercial Vacuum Red EUKSC5713A

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

Switch for Shop-Vac model QPL650 - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

I Need an on/off switch for a Shop-vac QPL30 vac?


... Shop Vac Vacuums

Hi! I'm interested in purchasing a G3 model ; however , the seller says that the machine was working perfectly and then when switching power on a while later , the machine was " dead " . Other than the brushes , power switch or lead , is there perhaps a fuse at all which could possibly have burned out ? Thanks .


Greetings from GoVacuum.com,Unfortunately there is no fuse on a Kirby Generation model. In my 10 years of repairing Kirby's as well as other vacuums, I will tell you that 9 times out of 10, when a Kirby Generation doesn't turn on, it's t ... Kirby Vacuums

Need 3' stick of plastic between vac head and vac switch. Lower end of stick will not stay in head.


Hello,Unfortunately the Fantom vacuum company has gone out of business, and no parts are available any more for these machines. Actually James Dyson (Dyson Vacuums) had some part in this company, and due to poor designs (mostly in thei ... Fantom Vacums Lighting Canister Vacuum

On off switch broken on my henry hound vaccum cleaner, where can i get a new switch?


... Numatic HHR-200 Henry Hound Bagged Canister Vacuum

The vac just goes red hot and switchs itself off no idea why. alyx pets 2000w is the model of the vac.


Its activated its thermal cut off. Check the filters - if the paper pleated cone filter is blocked throughly tap it gently to loosen dirt before washing it completely and drying it in a low temp tumble dryer (put it in a pillow case with a towel insi ... Vacuums

I have a model no APL625 shop vac and switch will not turn off. Where can I find a switch


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

I have a 3 year old NuTone CV 353W central vac system and recently the switch on the hose handle does not turn the system on from any outlet in the house. I have to plug the hose into the outlet and then turn the unit on from the switch on the cannister. Any help would be greatly appreciated. Thanks


A great way to check if your switch in the hose is bad would be to turn the hose sideways in the inlet. If the unit turns on you most likely need a new switch. ... Broan-NuTone CV450 Central Bagged Central System Vacuum

The main switch on my Henry will not stay down. How do I rectify this? I have undone the three screws inside the top but cannot get the top off to gain access to the switch.


... Henry Vacuums

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0382 seconds