Having problems with your Henry Numatic "" Canister Vacuum ?

My Henry model NV 250 Advice on fitting replacement suppressor which has only two wires. the original suppressor having four wires.

\015 Arcotronics main filter unit in the Numatic NV 250, 240 v, 680 w, 800 w max.\015

Answers :

Repair Help & Product Troubleshooting for Henry Numatic "" Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Henry model NV 250 Advice on fitting replacement suppressor which has only two wires. the original suppressor having four wires.


... Henry Numatic "" Canister Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Hello, I am looking for a wiring diagram to install a touch/dimmer switch by "Comfort" mdl # RH-934B - Darjung Ind Ltd. It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire. The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow - no lampcord. Thank you very much for your help!


The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp ... Vacuums

I replaced a Intermatic light timer with a GE 15086 timer. I have read several solution, but none fit my wire sceme. This is hooked up as a 3-way switch so the second switch can turn outside lights on manually. Here is what I have; Four timer wires: R B W G Wall outlet: B, B & R (Two), G, W bundle What ties in together to make it all work?


1) GE 15086 is not a 3-way timer.GE programmable timers are for single-pole switch replacement only. I have tested this timer, and own several GE timers, and many other brands.2) Open following link to identify timers that work for ... Vacuums

Hvr motor -four way switch ,two white ,and blue and brown wires -what goes where


Try this linkhttp://www.youtube.com/watch?v=97ZNEjKtu-gor this link one mite help you ... Henry Numatic "" Canister Vacuum

Just bought a Rainbow vacuum cleaner on/off switch and I need to know how to wire it since the original one has six connections and the new switch has only four. I'd appreciate your help. Thank


Call out tech. support number at 800-640-2033, and if you purchased from us, we give free phone support.....www.rainvac.com ... Vacuums

GE on/off timer for a bathroom fan - switch has four wires Green - ground White - neutral Black - power Blue - lead My fan has two - white neutral and black lead I have tried every configuration and cannot get the fan to work. Any suggestions?


I would guess that the black wire on the timer is the power in and blue is the power out to the fan (hook it to the black wire going to the fan) The other colors are right. ... Vacuums

I have a clarke bench grinder model 1002. I have a light that I would like to attach into the wiring though the grinder wiring in it's base. The light has two wires, and the grinder has a ground that is grounded to the base, a black that goes to a switch then to the motor. The white goes directly to the motor. where would I have to splice in the two wires from the light? I have a switch that I would like to put in for the light on off also.


Attach the white wire on your lamp to the white wire on the grinder.\012Attache the black wire on your lamp to the black wire on the motor side of the switch.\012This will give the lamp power any time the grinder is turned on.\012Yo ... Vacuums

I have a Kirby dual santronic 50, and two wires have been pulled out of the safety switch. the two remaining are green and yellow, and the two loose wires are red and yellow. What is the correct sequence? Thanks!


Throw it in the trash ... Vacuums

I need to know how to hook the wires up to the start switch. There are two wires from the external cord and two wires from the internal cord.


White wire to neutral black wire to hot if you post colors I could help you red ,orange, black,pink, blue, or violet are usually hot guessing a striped wire is usually neutral please post colors ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Trying to wire aa Nutone model 763RL bath exhaust fan/light. The conduit coming from the breaker box has a red wire, a black wire, a white wire and a ground. The fan has two white wires, one black wire, one blue wire and one green wire. I have wired the whites together, but do not know how to wire the blance.


... Vacuums

I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you


Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums

I shipped my brother PE 770 embroidery machine purchased sept of 2010, to a lady who perchased it on ebay. Had used only once. Everything worked fine.I shipped in the original formed styrofoam box. I removed the embroidery arm, releasing the locking plastic hook holdind the machine and the arm together. When to lady removed the machine first in the original plastic shipping bag, two parts fell out. Her photo she emailed showed a black plastic piece with two holes or pivot points.also a silver me


This is a link to the manual for this machine. Do you see a picture in the manual of the parts you are describing? Reply with a part number and I will do my best to help. ... Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

Wiring diagram I have a replacement main switch for my vacuum cleaner. Two blue and two brown but no diagram or markings on terminals to show which wire goes to which terminal


How to Repair a VacuumCleanerhttp://home.howstuffworks.com/how-to-repair-small-appl ... VAX Appliances 2000 Canister Vacuum

My son and I are trying to build a small motor for a school project. we have a 6volt battery 2 wires that we are hooking up to a spool of wire. We have two aposing magnets on each side of the spool of wire. the spool of wire is on a shaft and should turn when we touch it with the 2 wires from the battery. It just does not work. What are we missing here? Thankyou


Hello\015\012Please refer to the PDF document on how to build a small hobby DC motor.\015\012Go to the link below. Thanks\015\012 ... Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth


Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

Wiring Two wires (black and red) connected to the slider on/off switch have overheated and melted away the 90degree connectors. Will replacing just the connectors solve the problem or is it more complicated, such as a resistor, capacitor, etc.?


This is easy and hard. If only two wires connect to the switch, cleaning up the connectors and replacing damaged items should fix it. Don't do anything unless the unit is unplugged. Try this first: connect the two wires together and tape them up. ... Electrolux EL5010A Bagged Upright Vacuum

My plunger (bought in Chile) has 1. a metal filter, 2. a convex (not flat) metal disc with central hole for rod, 3.a metal disc with holes of two different sizes in circles radiating from the centre 4. plunger rod with screw and 5. a spirally coiled wire forming a circle. I cannot figure how to fit these especially the coiled wire. Help appreciated. Thanks


Place the coil in the hole and turn untill reach the desired height. ... Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available


Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2


Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.


Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0385 seconds