Having problems with your Hoover Breathe Easy U5250-930 Bagged Upright Vacuum ?

Vacuum is turning on and off intermittently - Hoover Breathe Easy U5250-930 Bagged Upright Vacuum


Answers :

Turn the vacuum ON.
\012Go to the plug while it is in the outlet, jiggle it and the wire going into it to see if there is a loose connection on that end.
\012Then go to where the wire enters the vacuum.
\012Jiggle that to see if that makes the vacuum stop.
\012If there are no problems found on either end of the wire, the next step it to open the machine and check the connections at the internal switch and the switch itself.
\012Let us know.
\012Gary
First I would turn it on and smell the motor area for any burning smell. It could be a short in the cord.Try checking the plug end and see if one of the prongs that plugs into the wall is bent or loose.Sometimes you can hear a clicking noise if the wire has seperated from the prong inside the plug end.A more dangerous approach is to plug it in and move the cord around and see if it cuts on and off with movement.If it's not the cord it could be the motor.You would notice the headlight flickering and possibly smell electrical burning if it is bad enough. www.sewvac.com
Repair Help & Product Troubleshooting for Hoover Breathe Easy U5250-930 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vacuum is turning on and off intermittently - Hoover Breathe Easy U5250-930 Bagged Upright Vacuum


Turn the vacuum ON.\012Go to the plug while it is in the outlet, jiggle it and the wire going into it to see if there is a loose connection on that end. \012Then go to where the wire enters the vacuum.\012Jiggle that to see if that ... Hoover Breathe Easy U5250-930 Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

I have the Eureka Whirlwind upright vacuum. All of a sudden there is no suction- the hose has suction but not main part. I have no idea- but the brush part is not turning??? should I get a new vacuum or is this an easy fix? thanks!!!!!


If the belt isn't turning then it has snapped. Check the top of the hood for two or three crosshead screws; two at the front and one under neath by the left hand side if looking at the upright from the front. Its easy to fix if you take your ti ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

Halo vacuum uv-st3290 the brush won't turn - Halo UVST Bagged Upright Vacuum


... Halo UVST Bagged Upright Vacuum

Vacuum is not turning on - Oreck XL Ultra Bagged Upright Vacuum


Try a ruling out a couple of things first before opening up the handle:\015\012\015\0121) First lets make sure your outlet has power\015\012 a) can you plug anything else in and have it work?\015\012 b) is the vacuum plugged ... Oreck XL Ultra Bagged Upright Vacuum

Vacuum will not turn off - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


(1) Please check the four screws that mount the upper handle to the lower handle. If they are not tight, the actuation of the switch may not be adequate.\015\012\015\012(2) Remove the four screws and the upper handle. you will see the r ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Cant turn the bag connect to get it off - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum

Oreck vacuum keeps turning off - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

Eureka vacuum won't turn on - Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum


... Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My vacuum kirby turned by itself - Kirby Generation 3 Bagged Upright Vacuum


The problem was that the piece that you connect to the wall outlet was broken. I purchased a new cord and it is working fine now. Thank you! ... Kirby Generation 3 Bagged Upright Vacuum

Why won't my vacuum turn on? - Fuller Brush FBHD1 Bagged Upright Vacuum


... Fuller Brush FBHD1 Bagged Upright Vacuum

Windtunnel vacuum brush won't turn - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Eureka Smartvac 4870 Bagged Upright Vacuum Smokes when I turn it on


Check the air intake! Its probably clogged! ... Eureka Smartvac 4870 Bagged Upright Vacuum

Replaced belt but isn't tight to turn roller - Eureka Smartvac 4870 Bagged Upright Vacuum


Are you sure that you have the right replacement belt? Here is a link to the belt you should have and the manual:Eureka 4870 Belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

I cannot get my beater bar to turn - Kirby G4 Bagged Upright Vacuum


Manual on how to attach the nozzle - HERE. Or you may watch the video on the bottom of the home page on goodvac.comGood luck,Rocky ... Kirby G4 Bagged Upright Vacuum

The brush isn't turning on my Kenmore progressive upright bagged vacuum model 116. The serial number is M80261402.


Replace the belt ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

My kirby will not turn on - Kirby Ultimate G Bagged Upright Vacuum


The kirby won't trun on if everything is not completely in place all the way. Check the vacuum bag position (the outer bag), make sure it is clicked in on the bottom, also check that the head of the vacuum is installed properly. Check your power uppl ... Kirby Ultimate G Bagged Upright Vacuum

Roller not turning - Sebo Automatic X1 Bagged Upright Vacuum


If the motor runs when you switch on, but the brush roll doesn't revolve, then there may be a broken belt. I wonder how old your vac is? Sebo belts are very high quality and they usually last 10 years at least.\015\012\015\012Before you go to t ... Sebo Automatic X1 Bagged Upright Vacuum

My orek has no power it won't turn on - Oreck XL Ultra Bagged Upright Vacuum


The spade connections are loose, take the handle apart and check them ... Oreck XL Ultra Bagged Upright Vacuum

The brush won't turn. - Kirby G4 Bagged Upright Vacuum


Are you certain the belt attached as it ws suppose to when you locked the front onto the base? ... Kirby G4 Bagged Upright Vacuum

Brush does not turn because belt is loose - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


You need a new belt that isn't stretched. You can get a replacement here:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush motor does not turn on - Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum


You could check Sears.com and click on parts then type in Model # or Part # this will get you a parts list you can choose from. ... Hoover U5453-900 WindTunnel Supreme Bagged Upright Vacuum

My kirby won't turn on - Kirby Ultimate G Bagged Upright Vacuum


Check your cord,maybe you have to replace it,they do sale replacements. ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1078 seconds