Having problems with your Hoover Company Wind Tunnel U53019 Upright Vacuum ?

Replace Powercord My dog destroyed the cord on my Hoover Windtunnel. I've ordered a new powercord and would appreciate direction on how to replace it. Thank you


Answers :

It has a cord relief to hold the cord in near the bottom, you will have to pull that out, the cord goes in there and comes out by the motor where the the wires connect. So you will have to pull the motor cover off to get to where they hook up to.
Repair Help & Product Troubleshooting for Hoover Company Wind Tunnel U53019 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace Powercord My dog destroyed the cord on my Hoover Windtunnel. I've ordered a new powercord and would appreciate direction on how to replace it. Thank you


It has a cord relief to hold the cord in near the bottom, you will have to pull that out, the cord goes in there and comes out by the motor where the the wires connect. So you will have to pull the motor cover off to get to where they hook up to. ... Hoover Company Wind Tunnel U53019 Upright Vacuum

A 'burn' hole has appeared in the Microwave Outlet Cover causing arcing (or similar sparking and blue flashing!). Would replacing this cover with a new one solve the problem or does it suggest something that would quickly reoccur? Would it be an economical repair or should we ditch the machine for a replacement? Thanks in advance etc it is appreciated.


... Vacuums

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!


... Hoover Steamvac F5860-900 Vacuum

HI THERE!!! I've noticed that you have been helping me with answering questions about Kirby vacuums with my links to my guides for quite a while now. I'd like to thank you for this, but I'd like to request that you use the direct links to my guides instead of copying from them and pasting it into the answer box. If you use the links, it will help me A LOT and I would GREATLY appreciate it. Thank you again for all of your help!!!! Marci (b0sslady2001)


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=534650\015\012HI THERE!!!\015\012Posted by b0sslady2001 on Apr 21, 2008\015\012I've noticed that you have been ... Kirby Ultimate G Bagged Upright Vacuum

My sister misplaced the instruction manual to her emerson microwave and I would like to replace the instruction manual. I do not have the model number available and only know she bought it at Walmart for around $60. I would appreciate any help. Thank you.


Hi,\015\012\015\012Since you do not have the model number of the Microwave, kindly view and identify the model from the complete list on the Emerson website by clicking this ... Emerson Vacuums

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!


Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums

The top of my 500ml/0.6qt thermal vacuum flask is broken and i'm not sure if i can get a replacement as the thermos is still okay. i would be grateful to know if i can get a replacement top so i don't have to buy a new one. Thanks meryl hawkins


Hi there,\012Well yes you can purchase a separate flask for your thermal vacuum, you may purchase them from the dealer or you can please post the brand of your thermos so we can help you to find the part.Good Luck!! ... Vacuums

I have a Tatung AllerFree Supra air purifying system (model AC-1200WH) I am looking for a replacement Hepa filter cartridge that will work in my discontinued advance air cleaner. I would appreciate any suggestion or help you could offer. Thank you, Barb


You can get filters from "New Vitality" $25 a filter if you sign up to get them every 3 months. ... Vacuums

We ordered parts for our Infinity pet pro vacuum : model NVC33C March-3-2011. We ordered a replacement roller brush and new drive belt. Our credit card shows the payment of $46.85 has gone through on March-9-2011. Our understanding of the shipping time was two to three weeks. Any information would be helpful. Thanks John Jamieson 12461 202 street Maple Ridge BC Canada v2x4t5


Hi,You'll have to contact the place you ordered the parts from. We are a DIY fix it yourself site.Handie andie ... Euro-Pro NV31 Infinity Vacuum

I just bought a used euro pro steam shark model ep903, has all parts but when I turned it on to use it water and steam poured out of the handle grip area. Am I not doing something right? The manual says to attach the brush directly to the hand grip but I can't use it without getting burned. Any suggestions would be greatly appreciated! Thanks!


... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

Omc specs 1989 rinker boat 4 cylinder gm/omc i need specs for: plugs, points,idle, prop size,etc. boat had been sitting for a while, i changed oil,points,plugs, new gas,etc. i can crank it, but it's a little rough and won't idle below 2000 rpms. any advice or help would be appreciated. thanks. tommy


You will need to repost this in the correct section, this one is for vacuum cleaner repairs. ... Vacuums

I need to replace belt #38528-033 on a Hoover WindTunnel vacuum model #U5463-960. I've had the vacuum for a long time and have misplaced all operational and instructional info that came with it. Any help would be appreciated. Thank you.


Replace the belt on a hoover washing machine ... Vacuums

I RECENTLY PURCHASED A HONEYWELL 2000i INVERTER GENERATOR AND I HAVE LOST THE USERS MANUAL SOMEWHERE IN THE HOLIDAY MESS. I AM LEAVING ON A TRIP IN A WEEK AND A HALF WHERE I WILL NEED THAT MANUAL. I'M NOT HAVING ANY LUCK FINDING ONE ONLINE AND WAS WONDERING IF YOU COULD DIRECT ME TO WHERE I COULD FIND ONE, OR SEND ME ONE. PLEASE! I WOULD APPRECIATE ANY ASSISTANCE. THANK YOU. .MICHAEL ALLISON [email protected]


You will need to contact Honeywell at this link below and fill in the form to request a free user manual for the Honeywell 2000i Inverter Generator:\015\012\015\012 ... Vacuums

Changing belt Please advise how to change the belt. I wasn't the person who took the belt off, didn't watch. Now it's just me and the belt. I had 2, but 1st one burnt right off. Apparently I didn't have in the right spot! don't want to waste the only other new belt I have. Pictures would be greatly appreciated!!!!!!! Thanks Tammy Can call 920-660-0680


Step 1: Lower handle to floor to change belt Step 2: Remove the two screws from the top hood on the footStep 3: Lift hood to remove Step 4: Lift right end of brushroll (the belt end) Step 5: Remove and discard belt.Step ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I was in the middle of using my vacuum when it quite on me. I tried multiple things including letting it cool off for a while as I was using it to vacuum my car outside and it was pretty hot. I also dismantled it according to the directions and looked for blockages and didn't find any and lastly I cleaned out the brush and put it back on. I am out of solutions. The vacuum is not that old; we have only had it for a few months. Any assistance would be appreciated. Thank You, Karen


Hi the problem you are more than likely having is with the wires that go into the vacume they are not that secure and do work loose.now if you remove the cylinder that you empty, now you see where the wire goes into the back of the vac, w ... Dyson Ball DC24 Bagless Upright Vacuum

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

Have called hoover about brushes they are saying that it is the whole motor and would be cheaper to by a new machine altogether. What do you think? Can just the turbine be replaced and if so what is approx cost? Is this something I can do simply by myself? If so how? thanks so much, Mel


You can get just the turbine. You would have to take the top cover off to do that. They are I believe around $50-$60 for one. Take the brush block out, then remove the screws from the bottom. There will be 2 long screws, they go into the turbine. ... Vacuums

I purchased a nordic microwave popcorn maker and misplaced the directions for making the popcorn. I need to know how much popcorn to put in the bowl and amount of oil if any is to be used. I would greatly appreciate this information, because as it is right now I cannot use the popcorn maker. Thank you for your time - will wait for your reply. Deborah Schmitt


The Nordicware Popcorn Popper is one that actually works in the microwave. The 3-Qt. Popper makes light and fluffy popcorn in about 4 minutes. Just place 1/2-cup of popcorn kernels in the bottom bowl and cover with the lid. No oil needed, makes up to ... Vacuums

Hi the foot pedal (button release) has broken on my Bissell lift-ogg. I have bought a new part but I am struggling to see how to fit it. any help would be appreciated thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee


Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

We bought a new home in march. It is a brand new home, with brand new First Alarm smoke/CO detectors. The very first night, we noticed the iving room (main) smoke alarm was "chirping". So we tried to replace the batteries, but when we did, all of the smoke alarms started going off (they are hardwired). We took out the new battery & dealt with the chirp. It is getting to be too much. So we are trying to fix it, but everytime we replace the batteries, the alarms are silent for a little bit, & then


... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

How do I replace the Powercord on a Fantom XT64K Vacuum. The powercord shorted where is comes out of teh housing. I need to open up the unit & replace but need a service manual of instructions. Thanks Father Lenny


I have done this several times, it's some what simple just take the unit apart and use the old diogram to replace the new one. Or take a digital photo of it opened so you have your own scematic. You should be able to purchess the cord at your local h ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1044 seconds