Having problems with your Hoover Elite U5061-900 Bagged Upright Vacuum ?
Roll forward motor stops. roll backward motor goes ? What's the problem?
Repair Help & Product Troubleshooting for Hoover Elite U5061-900 Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Roll forward motor stops. roll backward motor goes ? What's the problem?
... Hoover Elite U5061-900 Bagged Upright Vacuum
I have the Kenmore Model 116.36722600 Vacuum; while cleaning the carpets the vacuum all of the sudden stop working; I didn't smell anything burning; it was almost like someone unplugged it. I checked the rollers and I can move it forward and backwards with no problem. Do you think the motor just burned out? Does this vacuum have a fuse that I can reuse? I love this vacuum and would hate to toss it. thank you
Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900
Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
ProForce 1500 has suction but the brush roll motor stops working.
... Proteam ProForce 1500 Bagged Upright Vacuum
I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?
... Kenmore 34722 Grab-N-Go Upright Vacuum
My irobot goes backwards a short way, stops, turn, goes backwards some more, repeats the process over and over until it gets stuck. No beeps, no talking.
Your problem is the circle dance problem or 9 beeps errorsearch the site and you find solutions ... iRobot Roomba 530 Robotic Vacuum
Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?
... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz
Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum
Hoover Elite motor runs when moving backwards but not forward
Are you sure its not just your belt on the beater of head slipping and needs to be replaced? ... Hoover Elite Rewind Bagless Upright VacuumVacuum
My vacuum goes backwards easily, but forward with GREAT effort..
... Hoover U6446-900 WindTunnel Bagged Upright Vacuum
Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do
I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum
Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.
The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
This is not an electrolux problem, but I am hoping one of the experts can answer the question. I have a Sears air compressor that suddenly stopped working. After looking at how the motor case is put together, it appeared that it would essentially have to be destroyed to get it apart and into the motor. I received a new compressor for my birthday so I decided to tear into the old one to do some diagnosis. After getting into the case where I could see the motor/pump, I have discovered the prob
This is intersesting. I think the fuse is simply a heat sensor. If you by pass this the only problem you may run into is if the motor over heats it my eventually burn out. However, for what you are using it for overheatin should not be an issue. This ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance
... Kenmore 34722 Grab-N-Go Upright Vacuum
My Hoover duros s3590 just stopped running. The motor started up and then just powered down and won't start back up. Is this a faulty on/off switch or a motor problem. I'm weighing the +/- to fix or buy a new vac. TIA
... Maytag Hoover Duros S3590 Vacuum (Canister)
My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A
This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum
I fear the motor has failed on my Electrolux Oxygen EL6988D. Just six months after the warranty expired, I was vacuuming when it suddenly stopped. There was no blockage in the tube and it wasn't working hard or long . . . it just stopped. I looked around the Internet and it appeared that many similar Electrolux units have a fuse. I hoped my problem might just be a blown fuse, so I took the machine apart. There are two small printed circuit boards, but no fuse. There is an in-line
Hi,\015\012\015\012I don't think you need a new motor, but please stop testing the machine with live power. It's dangerous and unnecessary. Your tests indicate to me that the motor is fine and your thermal-fuse - I think this is wh ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa
... Electrolux Vacuums
I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.
You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums
Not working I hit the switch and there is no sound of a motor. Nothing is happening. It was working seconds earlier and suddenly it stopped. The plug was in and I replugged it into the outlet. Still, no power and no motor sound. Does this happen if the belt goes? Thank you, Jill
If it was just a broken belt you would still hear the motor running. most likely its in your cord or switch. check the main cord, connections to the switch, and also the motor supply cord that goes from the handle to the vacuum head. ... Oreck XL Ultra Bagged Upright Vacuum
My bissell carpet cleaner won't roll forward on my rug. i borrowed it. is it only supposed to roll backwards when I use it?
... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
I have a Dirt Devil Vision self-propelled vacuum cleaner. Recently, the self-propelled feature is stuck in the backward mode, so it only goes backwards! I can get it to go forward if I push really hard (i guess it is good for a workout!). I try to turn off the propel feature completely, but it will not turn off. please help!
Hi, the problem you are having is going to be with the switch that controls the forwards and backwards settings so with this stuck in backwards their is no way you can get this turned off, the other problem is your not going to be able to replace thi ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks
If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum
Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v
Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums