Having problems with your Hoover F5826-900 SteamVac Upright Wet Washer ?

I can't get my attachment to put out the solution

Answers :

According to www.vacuumpartstore.com, for model #'s F5903, 5904, 5905, 5906, 5910, 5912, 5914, and 5915, you need Hoover SteamVac Bare Floor Cleaning Attachment (old # 48417003). You can get it at www.amazon.com for $7.99.
Repair Help & Product Troubleshooting for Hoover F5826-900 SteamVac Upright Wet Washer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I can't get my attachment to put out the solution

According to www.vacuumpartstore.com, for model #'s F5903, 5904, 5905, 5906, 5910, 5912, 5914, and 5915, you need Hoover SteamVac Bare Floor Cleaning Attachment (old # 48417 ... Hoover F5826-900 SteamVac Upright Wet Washer

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?

Yes don. call the store where u rented and tell them. ... Vacuums

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it

My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I

Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Solution seals The seals on the bottom of the solution tank are broken. I need to get a replacement as well as a breakdown on how to put alll these parts back together????

Please use the following link:\015\012http://www.hoover.com/parts/?category=carpetcleanertanks&part=42272134\015\ ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do you put the telescopic wand down? Just got a new dyson 17 and I cant use it cause I cant get the dang wand down..

Make sure your handle is snapped in all the way on to the machine, that will release the clip on the hose to allow for the wand to slide in. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?

Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate

Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

Cant get the belt to pick up on the hook when trying to get the head attachment working

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=844275\015\012Generic problem for all Vacuums\015\012Can’t get the belt to\015\012Posted by jltbo ... Vacuums

I have a beam adjustable wand with an attachment on it meant for hardwood, or linolium floors. The wand is broken so I would like to take the attachment off and put it on a new wand. How do I get t

... Beam Vacuums

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

Cant get it to spry solution on to carpet hose pluged if so how d

It is because the pump belt is worn or stretched. Here is the replacement you need:Bissell Proheat Pump Belt ... Bissell PowerSteamer Deep Cleaner Plum Upright Vacuum

Can't get the cleaner to put out any cleaer solution how can I fix this?

Hi Anne! Sorry to hear you're having difficulty with the spray.Here's a quick link to troubleshooting steps to assist you:\012\012htt ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition

Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

I cant get the water solution to come out of the tank

You must of put the tub on wrong. other wise it would be working fine ... Kirby Ultimate G Bagged Upright Vacuum

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o

It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Cant get my bissell powersteamer #1685 to dispence the water/ cleaning solution and have lost the opperators manual

That means that the pump belt is worn or broken. You can get a replacement and view the manual here:Bissell PowerSteamer Belt and Man ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I can't turn the belt off of my Kirby vacuum. I had the front off of it earlier to attach the hose, but now when I put the front back on, I can't get the belt to turn off. The lever twists about 3/4 of the way around, but will not go the rest of the way.

Turn the front part to the green so it is level and then twist the front to the red make sure the belt catch the hook as you twist it then if the belt is hooked just put it back on the vac like normal and lock it in place then twist it back to the gr ... Kirby Ultimate G Bagged Upright Vacuum

Shutting off my vacuum has been shutting off in middle of use and i dont know why its like its over heating and i cant use it again for almost an hour is there a solution to this? or do i need to get a new vacuum?

It has a built-in temperature sensor which prevents it to be damaged from overheating. That's why it shuts down. It just needs to be opened up and cleaned thoroughly. Start with the hose if it has one and let someone who is handy with electric applia ... Vacuums

I cant get my kirby to blow out...bag is removed from seating...its plugged in...i attach the hose to the place where the bag goes, but it wont run

I did get it to work! It was a struggle, but It finally hit that hidden switch just right. The hose attaches to where the bag goes, and it just wouldnt seat properly. I suppose there might be some wear there on the hose end that twists in . ... Kirby Vacuums

Kirby shampooer The suds are not coming out of the shampooer. I made sure it was connected right. The sponge filter and the cap are attached. i have a g4 vacuum and the screen in in properly.. if i move at a snails pace i can get spots of suds about every 6 inches or so but not a lot. i have adjusted the on and off, if verified the video its put together correctly but it acts like no suction .. i thought of a small hole in the hose for the suds and cut off about 1 inch it act better but not by

On the shampooer tank, remove the screen cap from the little hole that the shampooer hose plugs onto. Clean the screen and make sure that it is not plugged up with debris. Make sure that the screen is securely glued to the cap all the way around the ... Kirby G4 Bagged Upright Vacuum

The belt is broken and i cant figure out how to get the wheel of to put a new one on

The control height adjustment knob should simply pull off - grasp it gently and pull off. Then locate the screws on top of the floor head to get into the belt area. ... Euro-Pro NV31 Infinity Vacuum

My belt broke on my kirby upright, I took the roller off and put the new belt on, but I cant get the hook to hook on the belt.

On the front of the nozzle is a big knob that you turn to load the belt. Take the nozzle of of the vac, turn the knob to catch the belt, keep turning it until it stops. You will know if the it caught the belt, it will be hard to turn. Put the nozz ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0505 seconds