Having problems with your Hoover F5835900 Upright Steam Vacuum ?

Not pulling water up. let out but seems to be blowing out and not pulling up water


Answers :

Hello
Click HERE to get the manual. Go to figure 3.1 and clean the filter if necessary. Go to figure 3.8 and make sure pate E is clear. Make sure the part is slides up against when inserted downward is clear. Go to figure 3.11. The slotted holes in the recovery tank lid must be clear. Finally the recovery tank tank must fit snugly and air tight. I hope this works
Repair Help & Product Troubleshooting for Hoover F5835900 Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Not pulling water up. let out but seems to be blowing out and not pulling up water


HelloClick HERE to get the manual. Go to figure 3.1 and clean the filter if necessary. G ... Hoover F5835900 Upright Steam Vacuum

Keurig b200 problem; When brewing with cup in unit water will pass into cup and it seems when k cup is full the grinds puch up through the top and water overflows. i pulled out the k cup holder and cleaned so their is nothing that is obstructed included the piercing pin. brewed [product does come through but does not seem to allow it to come through fast enough or if it supposed to be pressurized it is losing its seal on the top of the k cup


... Vacuums

I used the Scooba 390 for the first time this weekend and it seems that the robot had problem sucking up the dirty water from the floor. When I emptied the dirty water tank, there was hardly any dirty water. Can you please let me know what can cause this problem?


... Roomba iRobot Scooba 390 Floor Washing Robot

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?


Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop ... Rainbow E series Canister Wet/Dry Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

My Rainbow Aquamate II has water flowing and there are no clogs in the tubes, however, the white water basin does not seem to have any suction pulling the cleaner from the bottle. How can I fix this???


Hello,kindly check for a clog and also follow the instructions below.when you experience no suction pulling the cleaner from the bottle,it's either you are having a clog or probably the water gauge is not ok.\015\012\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

My Steam Vac does not pick up the water from the carpet why? When I pull the Vac backwards to **** up the water it sucks it up sometimes and sometimes it doesn't Is there a manual I can get I seem to have misplaced mine.


Ebay,google,or the manufacturers website they usually have downloadable manuals... ... Hoover F5858-920 SteamVac Wet/Dry Vacuum

Hoover f5835-900 will not pick up water. seems to be blowing air


HelloClick HERE toget the manual. Go to figure 3.1 and clean the filter if necessary. Goto ... Hoover F5835900 Upright Steam Vacuum

My Bissell CM 2000 shampooer does not seem to be pulling in and dispensing the shampoo as it should, although is spraying the water just fine.


... Bissell Vacuums

I have a Danby SHCC6026-2 with the humidifer, dehumidifer, hepa system. It is not running as it used to in that warm air used to blow from the side and is no longer doing so. We only use it as a dehumidifer in the basement. It is damp down there and the unit does not seem to be registering the levels correctly anymore. It is not collecting water.


... Vacuums

It will empty the cleaner but will not spray water filter is clean spray heads were taken off & i could blow threw them is it a case of no prime in pump if so should i fill pump i had this thing all apart and i now know evry inch of this matchine when i pull the triger it sometimes will spray for a sec.but thats it i also took the switch out and air goes threw when i press the switch if it is the prime in the pump how can i fill the pump . what hose on the pump will prime i thankx for your advic


The problem is most likely that your pump belt is worn, stretched or broken. Here you can get the belts you need and view the manual:htt ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Attachments The hose attachment doesn't spray out water. it seems like the trigger doesn't pull back enough. Is there something I can do to fix this or do I need to get a new part?


Most likely will have to replace either the nozzle valve or the hose comes complete, so if the nozzle pieces are available, then replace the complete hose asm. ... Hoover V1 SteamVac SpinScrub Vacuum

I have a Husqvarna Viking Designer sewing machine. The fuse blew in the machine and I am having trouble finding a replacement fuse. It is a T3.5/250v glass fuse. Please let me know where to find one. I have searched the internet high and low and can't find one. Radio Shack has a 3.0amp 250v slow blow fuse whick seems to be the right dimensions. Willl that work. Otherwise, I am not sure what to do and can't afford to take the machine to a repair show. Thank you.


That fuse will work no problem. There is no harm in trying it.The machine probably requires about 2 amps or less under normal operation. Being a 3.0 amp slow blow fuse, it will withstand short bursts of extra current when your machine get ... Vacuums

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I've tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That's what leads me to believe there is a clog. If you can help, please do. I like the product and haven't been able to use it for awhile because of this. Thanks.


I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rec ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Royal 7910 extractor and even though I vacuum before cleaning the carpet, by black cocker spaniel's hair gets pulled into the plastic pick-up attachment and I cannot find an easy way to clean it out. I have tried taking the screws out to separate the halves, but it seems as though they might be glues together. I have run water from a sink sprayer though the openings with some degree of success, but it still is pretty cruddy. I have tried snaking pipe smokers pipe cleaners up the pick


One person wrote this in a review:\015\012Most home carpet extractors are very difficult to take apart for cleaning and maintenance. The Royal 7910 is the exception. No tools are needed to take the front housing off to clean out all the pet hai ... Royal CE7910 Wet/Dry Vacuum

My steam-vac carpet cleaner doesnt seem to be pulling the dirty water back out of the carpet.


The most common reason for this is that the lid is not fully seated on the dirty water tank. Be sure to hook the lid in front, and then snap it in place at the rear. Another problem could be that the duct is missing from the front of the tank. ... Hoover Vacuums

My steam mop S3501 seems to be clogged because of mineral build up. When it heats up it blows the mop head off from the pressure. I had not been using distilled water. Is there any way to clean it so the steam can get through again?


I'm having the same problem. Do you think soaking the head in CLR and then maybe cleaning with pipe cleaners would work? ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Hoover Steamvac model F5808. It no longer sucks up the water and seems to only blow air. I already removed all the hair and fuzz buildup... what could be wrong? I no longer have the manual to look at.


... Vacuums

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The water tank on my bissell proheat 2x is not keeping the clean and dirty water separate. I;ve checked the container and there doesn't seem to have anything wrong with it. Also when I switch the machine on you can see the "washing" action, after a few minutes this seems to stop - there is water and forumula in the machine. Only had it a year!


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Have a new pro heat 2x. seems to work well but does not seem to extract water. It has the two in one reservoir and there is no dirty water around the clean water bladder. What is the problem?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt


Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve


HelloGrasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually insp ... Vacuums

My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett


I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums

My power steamer seem to be putting down water and scrubbing but it's not picking up the water it puts down. Also, it doesn't seem to be using any of the cleaning solution


Trythe following suggestions to see if you can get your machine suctioning properly:\012\0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0499 seconds