Having problems with your Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum ?

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


Answers :

You will have to replace the complete hose asm, part # 90001337
Repair Help & Product Troubleshooting for Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I


Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Vaccum is making a loud high pitched sound, doesn't work well through the hose or the floor piece and shuts its self off after about 5 minutes. I have cleaned the entire vacuum out several times but this problem persists. Usually after I clean it, it'll work for a couple months, not this time. Vacuum is only 2 years old, is this typical?


... Dirt Devil Featherlight Bagless Upright Vacuum

Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.


... Sanyo Vacuums

Cannot get hose to go back down.


Hi there SmartAlec from NelsonVacuums.com.au here. I think you will find that the hose will lock in easier if you remove the clear bin of the dyson. If it is not this then ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The plastic coupler that hooks onto the propane tank cracked. There is a replacement part, coupler, regulator, Y hoses to the main and side burner, avail but how do you disconnect and re connect them? The hoses have a clamped metal ban attaching them to the burner tubes can't get them off. Thermos Barbecue Model # 461410707 Thanks much.


Wrong forum to help you out. ... Vacuums

Can not get Shark steam mop to steam, green light is on? Purchased 5/4/09, Registered Product 6/2/09 Cynthia Friesema 973-222-7068 please call cannot get through on your phone line!!!! Tried many times, just gives me a fast busy signal every time I try to call !!!!


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.


Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.


Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet


Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I've only used it a couple times and I don't see where it is working. Has anyone else had this problem?


Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected in ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Getting part My repair shop cannot get the part for my filter queen. It's the plug in the body of the machine that the short plug goes in from the hose. It's been bent. Can I get a replacement part?


Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps. ... Filter Queen Majestic Canister Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

We cannot get the hose attachment to work. The


Try this guide.\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We owe ionic pro turbo air pur. ever since we cleaned it first time, it's making this static noice and it get really loud at times that it makes hard to sleep. What can we do?


Water or debris in the collection blades or wires can cause a snapping or arcing noise. Water should have dried after a day or so. Look for a hair or lint that is between the blades and wires. Ionic also suggests that the noise may be from misalignme ... Vacuums

Dc07 model, cannot get it to stand fully vertical upright. It is as if something is not sliding back into position right. Don't want to force it in case something breaks. The upright of the cleaner has been dropped from time to time. Any thoughts on sorting it out?. Thanks a lot. M


Hi, Try this quick repair and see if this fixes your Dyson in terms of not going in the upright position: This is a frequent problem that we see come in on Dysons. If this doesn't fix it, please feel free to just use the clarification req ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I am trying to change the coupler on a KitchenAid blender model number KSB560ER0. It is a recessed coupler and I cannot get it to unscrew in the clockwise direction no matter how hard we try.


... Vacuums

My Infinity Shark vacuum has lost suction. The pitch sound changes very soon after turning it on. I believe the lower hose is clogged, and I cannot get the body cove unattached where the hose bends upwards into the chamber. So much for their claim of never losing suction!


... Vacuums

There is a clog in clear tube that sends trash from floor to cylinder. have pulled out lots but cant get really far in there. can I take the hose off somehow and get in there


Try using a hanger and see if you can snake it out there might be a small hose on bottom of power head,i hope this helps thanks ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.


It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I cannot get the sprays from either the bottom or the handpieces to work. I only get a short "gurgle" of fluid when I first press the controls. I have cleaned both the top and bottom cap and insert parts, and I have turned the machine off and on numerous times, have allowed it several minutes to warm up. But still no luck. Bissell Turbo 2X 9500 series (3 years old) D B Davis Camas,WA


It sounds like the pump has malfunctioned. I own a Bissell Big Green Clean Machine.You can actually order a 50 foot hose and run it from the sink to the hand piece or the part that is supposed to spray to the floor. This hose can handle ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK.


Sounds like a bad motor bearing. If it is, then you would have to replace it. Could be the brush roll, did you check the ends to make sure they turn easily? ... Vacuums

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0805 seconds