Having problems with your Hoover F5858-910 SteamVac Vacuum ?

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position


Answers :

This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue to put the tooth back into place. it works ok now. Not like new but it will hold. this was sorta easy but i enjoy fixing things. If your not handy i wouldnt recommend you try it. i am in the process to making an aluminum version of the tooth so it wont break again.
Repair Help & Product Troubleshooting for Hoover F5858-910 SteamVac Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position


This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue ... Hoover F5858-910 SteamVac Vacuum

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

The unit will no longer lock in UPRIGHT position. Thank you


On the vacuum main housing next to the pedal there are three notches. Check your pedal against these notches. It may be a simple off-alignment. Otherwise, you may need to replace the pedal. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

I took my Dyson DC 25 Animal apart to clean it, and now the red foot pedal won't lock the vacuum into the upright position anymore. The trouble is the spring pin for the pedal popped out and I can't figure out where it is supposed to go.


That spring thing goes where the pedal screws into the side. When 'facing' the dyson in the front, it's on the left side. The spring's circle part and short stem section goes into a divot area on the pedal. The other end is tensioned (braced) a ... Dyson DC25 All Floors Bagless Upright Vacuum

Dirt devil model 08633 handle wont lock in upright position


... Dirt Devil Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Miele s7000 I clicked my upright into sitting position and accidently bumped the foot release knob. The body fell back and now I can not get it to click back into upright sitting position. Something is now in the way of it locking into place. This happened last year and it was under warranty. it no longer is and I would like to be able to fix it myself in the future. Can you help me? Thank you. Kacee in Oregon


... Vacuums

Hoover windtunnel tilt mechanism won't remain locked in upright position or at any of the fixed angle positions - now any slight bump and the lock releases. Normally you must manually use the small foot pedal release on the left side as you face the vacuum from behind.


Hello, stanI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took


... Vacuums

Dyson dc07 will not lock into upright position


- Stand behind the vacuum cleaner and look at the right-hand side wheel\015\012- Remove the AI PIPE (it has two purple buttons that you push together to lift it up and out - it looks like a Tuba)\015\012- Lay the handle down and look for ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Miele Twist vacuum will not lock into the upright position. Also I sucked up a tassel from a throw pillow and have a clog. I took off the little clean out plate on back...it isn't in that par


... Miele Vacuums

Oreck XL vacuum will no longer lock in the upright position.


... Oreck XL Ultra Bagged Upright Vacuum

Handle wont go to upright position


The red pedal has slipped out of position. On both ends of the red pedal you'll see metal rods (the axel of the pedal). On one side you'll see the metal rod sits into a long groove, on the other side you'll see the metal rod sits into a round hole. T ... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson DC01 will not lock in upright position - Dyson DC07 Bagless Upright Cyclonic Vacuum


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hose disconnected There is a clear circle on the part where the hose connects to the cannister (above the orange ball) that is in a position that has the hose disconnected. I can move the circle so that the hose connects, but it won't lock in that position. Help!


This video may help ... Dyson Ball DC24 Bagless Upright Vacuum

My DC-25 will not return to the upright position. I emailed Dyson support and the response was: "The DC25 stabilizer wheels will not lock into position if the “spokes” on the red pedal are not seated correctly." I agree with that assessment, but cannot figure out how to get the spokes on the red pedal to seat correctly. The manual is useless for this problem since that part of the vacuum cleaner came already assembled, so the manual does not address it. Help.


It sounds like the undercarriage unit has failed. It is a common problem on ball models. The DC25 is a recent model so would still be under Dyson's 5 year guarantee. Get them out to it. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

We cannot get the Miele S7210 Twist back to the upright position. The foot lever appears locked. We fear forcing it back to upright.


... Miele S7210 Bagged Upright Vacuum

Dyson will not lock in the upright position - Dyson DC07 Bagless Upright Cyclonic Vacuum


There is a video guide here for this: \012\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The canister wont lock in position like theres a part missing to push it up to lock in


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Wont click back into upright position - Dyson DC07i Bagless Upright Vacuum


... Dyson DC07i Bagless Upright Vacuum

Part that locks vacuum in upright position, I cannot find


I have the exact same problem as you described it. I was hoping to find this plastic part reading 38719-006, and it seems it is not available as a part by it self. The attached image includes both the part you will need to purchase 43516010 along w ... Vacuums

My Dyson vacuum cleaner wont close & Open to the upright position to allow vacuuming to take place


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC27 Animal is stuck (Locked) in the upright position. Everything seems to be ok with no apparent cracks or breakages. I don't want to force it in case something snaps.


Dysons are notorious for this problem. You will have to just force it and clean any obstructions. ... Vacuums

Will not lock into the upright position and has lost suction from the brushes


Upright Lock Assembly has broken ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Wheels the wheels on my vacuum bunch up, have replaced them and still doing it, also it will not lock in an upright position, something fell off do not have part


The axle for the rear wheels have worn into the cut outs in the body that it goes through and they are rubbing on the wheel wells. This common for this vacuum model , the only real fix is to replace the body assembly. Sears will have to do this, this ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0905 seconds