Having problems with your Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum ?

The brushes won't turn. - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


Answers :

(1) Assure the Brush Control on the hood is NOT set to the OFF position.
\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.
\015\012(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
\015\012(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
Repair Help & Product Troubleshooting for Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes won't turn. - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum


... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Hoover steamvac f6024-900 manual - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover max extract brushes not turning - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover SpinScrub brushes not turning - Hoover V1 SteamVac SpinScrub Vacuum


Hi There,Here's a very helpful Tip that I've written that explains step by step how to diagnosis the Hoover SteamVac when the brushes stop spinning. This will also walk you through how to replace the brush gear turbine assembly if you f ... Hoover V1 SteamVac SpinScrub Vacuum

Where do i plug the hose into the vacuum - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


Hi There,I'll be happy to walk you through step by step how you can attach the hose to your Hoover SteamVac.Here are step by step instructions for you:Step 1. To prevent possible leaking, removeclean solution ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Manual for Hoover F5880-900 - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


Download the manual off this linkhttp://hoover.com/support/manuals/?q=f58660 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover f7452900 brushes wont turn? - Hoover F7452-900 SteamVac Upright Vacuum


Make sure that you have it on the carpet setting and not the hardwood/tile setting. also if you used the hose, make sure that the little door is closed. if all checked... remove the recovery tank, there should be a rubber grament on the stand pipe un ... Hoover F7452-900 SteamVac Upright Vacuum

Steamvac is not sucking water up - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


Probably is clogged up somwhere ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover Deluxe Elite Rewind vacuum has stopped working as it should. The airflow indicator snaps on almost immediately after I turn it on whether the hose is connected to the brush or not. There isn&


... Hoover Elite Rewind Bagless Upright VacuumVacuum

Brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Remove the brushes by pulling down at the ends.\015\012Is the square pin present on the top of one brush? It should be approximately 1/4 inch square, and two inches long. That connects the brushes to the drive mechanism.\015\012(2) ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

BRUSHES NOT TURNING - Hoover F7220900 SteamVac V2 Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F7220900 SteamVac V2 Upright Vacuum

Will not dispense water - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


There are many reasons for this. Most shops give free estimates. Give one a try. ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Brushes donot turn when asked to shampoo - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


The brushes are turning by an air driven turbine. The turbine has a \015\012pivot bushing made of steel inside of it that gets rusty because of the \015\012water that is running through it. The turbine will have to be replaced. You can find a genu ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Be sure the speed switch is set to carpet. Also remember the brushes won't turn until the handle is tipped back. If this is not the problem, remove the brush and insert a flat screwdriver into the square hole the brush pin goes into, and be sure it t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Spinscrub F 7412-900 brushes wont turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The scrubbing brushes do not turn. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The rotary spin brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Belt either came off or broke ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Agitator brushes wont turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes are not turning - Hoover F7220900 SteamVac V2 Upright Vacuum


There is a plastic shaft on the back of the block brush (spin \015\012scrubbers),\015\012 these wear out or break. You may need to replace the block brush. Or \015\012if the shaft is not broken it could also be the Turbine Gear. This is \015\012wh ... Hoover F7220900 SteamVac V2 Upright Vacuum

Brushes do not turn - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


Check the brush block to see if the shaft that goes into the turbine broke off, replace brush block if it did. If ok, then the turbine may be clogged up, either clean it out or replace the turbine. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Need a manual for Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Brushes don't turn - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


I had the same problem and found a manual online. I never realized that there was a filter in the bottom of the machine. There are 2 red tabs, squeeze them together and pull ( I had to use a pair of pliers to pull). Note which is top and which is bot ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Srub brushes not turning - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


You will find broken belt or something is jamming it ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1460 seconds