Having problems with your Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum ?

Looking for someone to instruct me on how to take apart my hoover steam vac so that I can check for clogging. It just stopped extracting water from the rug everything else sounds fine. The return holder is in place and has been checked many times. Any help?


Answers :

First remove the dirty water tank then turn the unit on if your facing the front there is a duct on the right where the tank sets there should be a black seal around it if you have suction there then you will need to check the tank
Repair Help & Product Troubleshooting for Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Looking for someone to instruct me on how to take apart my hoover steam vac so that I can check for clogging. It just stopped extracting water from the rug everything else sounds fine. The return holder is in place and has been checked many times. Any help?


First remove the dirty water tank then turn the unit on if your facing the front there is a duct on the right where the tank sets there should be a black seal around it if you have suction there then you will need to check the tank ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

My full size bissell sprayed the room just fine, but now it won't **** up the water. Help! The container is closed and locked into place, and the bissell sounds fine.


Wish you had provided the model number, as they are different. The most common, if there is a flow indictor, is the filter there clean or clogged. The other possilbe, there is a ovule black seal that sits on top of the clear window noozle and the e ... Vacuums

I have a HBS 20 fan. I've had for a few years but seldom used. I turned it on last week and it made this humming sound. After a few minutes it started running just fine. However, now it does not hum or do anything else. What is wrong & how can it be repaired? Please help. Thank you


It ispossible that the capacitor for the motor is weak . You can access and replace this capacitor if the motor is humming and getting warm. replace with the same value and test. If it does not work then check the windings of the motor, if short wi ... Vacuums

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell proheat 2x 8920 series will not dispense the cleaning fluid from the little tank. The water sprays out fine and everything else works, it just wont spray out the cleaning solution. Please help!


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators


Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums

I have a bissel proheat 2x and everything works on it except the bottom sprayer. I cleaned everything out on it and everything is in place but it wont spray. Can someone help me through this to get it working?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???


The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums

Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD


... Singer Vacuums

Dyson dc14 brush bar is not turning at all. Everything else seems to be fine. I just replaced the brush bar but still no movement. What else could it be?


Hi there,I'm sorry to hear you're having difficulty with your DC14 Animal. If the brushbar doesn't rotate, please check you have the brush control set to 'Carpets', not 'Hard floors'. The brushbar will not rotate when the machine is standing ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Hoover Steam Vac won't extract water from rug anymore..


... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Really LOUD Just recently this vacuum went from the normal everyday vacuum to now sounding louder than my power saws in my workshop. Checked for clogs.. everything is clear.... cleaned it all over and then turned it back on and.... The neighbors thought I was running a saw mill out of my house. HELP!


Its the belt if it is a savvy.Have the same problem ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.


It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

Hoover.com/Model F72229RM Brushes won't spin everything else works fine.


... Vacuums

HORRID NOISE I have took it all apart and thoroughly cleaned it. It is still picking up dirt etc. But the noise sounds like its taking off. It is not that old so can not be the engine my mother has one that she has had much longer and is fine she has also checked it it is out of guarantee but is working the noise is terrible. Can you help???


Hitake out the belt and brush. Switch on. If the noise has gone you know its the brush. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brushes on the Hoover F7452-900 SteamVac Upright Vacuum will not spin but everything else seems to work fine. How can I solve this problem?


There is no belt. This unit uses a turbine that uses air off the vacuum motor. There is an actuator arm that moves rearward when you depress the handle release and then lower the handle to use the vacuum. That engages the turbine and spins the brushe ... Hoover F7452-900 SteamVac Upright Vacuum

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.


Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!


The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Eureka 431BX suction stopped working. Roller still goes. Please help! Everything else is working great.


Even though the brush is spinning, you probably need to replace the belt\015\012because ... Eureka 431BX Bagless Upright Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!


You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums

I have a Kenmore Progressive Upright Vacuum - Purple, and it worked just fine. I emptied the canister (like always) and put it back in place. I turned on the vacuum to it immediately shutting down (motor) and only the lights come on. There is no movement/noise/suction at all! Any suggestions? I have tried everything. I have no idea why it did this.


Make sure that something didn't fall into the fan assembly in the base when the canister was removed. The motor should have an overload reset switch. Try moving the motor manually (power plug out) to make sure that it isn't bound up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0610 seconds