Having problems with your Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum ?

Hoover steam vac all terrain turbine gear assembly

\015 Hoover steam vac turbine gear assembly installation instruction. Bought turbine gear to replace. Just need instructions to take the steam vac apart to get to the turbine.\015

Answers :

Hello,
\015\012
\015\012I'd be happy to walk you through this repair. Unfortunately this is a very common problem with the Hoover SteamVacs.
\015\012
\015\012Here's what you'll need to complete this repair:
\015\012- Hoover Turbine Assembly For Model F5866-900 Part # 43191001 or 90001354
\015\012- Phillips Head Screwdriver
\015\012- Flat Head Screwdriver
\015\012
\015\012Step 1. Remove both the clean solution, and the dirty solution tanks from the machine, and press the handle release pedal so that the handle is laying down flat:
\015\012
\015\012
\015\012f9817d2.jpg\015\012
\015\012Step 2. With a flat head screwdriver, pry off the rotating brush speed indicator knob:
\015\012
\015\012
\015\01255c72db.jpg\015\012
\015\012Step 3. Unscrew the silver screw that's at the very top of the see thru suction port where the dirty solution tank rests.
\015\012
\015\012
\015\01291c5d91.jpg\015\012
\015\012Step 4. Turn the SteamVac upside down so that the brushes are facing upwards. There are four clips that hold these brushes in place. You'll need to remove the brushes from the machine by squeezing the four tabs while pulling upwards at the same time. The picture actually only shows the two tabs on the right hand side being squeezed, but the tabs on the left hand side are in the exact same location:
\015\012
\015\012
\015\012903753e.jpg\015\012
\015\012Step 5. Once you've removed the brush block from the machine, there are 4 screws on the bottom that need to be removed. Keep the two silver screws on the very corner in place, you won't need to remove these. Remove the four screws that I've highlighted in red:
\015\012
\015\012
\015\0128f04e58.jpg\015\012
\015\012Step 6. Turn the machine back over right side up, so that the brushes are on the bottom. There are two clips that hold the top housing in place. Insert your flat head screwdriver in between the top and lower housing in the rear of the machine close to the rear wheels, and pry upwards to unclip these clips on both the left and right sides, then remove the top motor housing from the machine.
\015\012
\015\012
\015\01219c46e5.jpg\015\012
\015\012Step 7. You'll now have complete access to the turbine. Remove the two silver screws in the front of the unit that hold the turbine in place, as well as remove the front hose from the turbine:
\015\012
\015\012
\015\012
\015\0129f8ce8d.jpg\015\012
\015\012Step 8. Once you have removed the two screws you'll be able to lift the turbine up. There's a second hose in the rear of the turbine that you'll also need to remove before you can remove the turbine completely. After you've removed the hose, take the turbine out of the machine. You'll notice to the immediate left of the turbine other hoses that connect to a black circular part. This is actually the pump that sprays the water on the floor. If you ever have the problem where the clean water solution will not spray, it's a good possibility that this part needs to be replaced.
\015\012
\015\012Simply install the new turbine, reattached the hoses and two front screws. When you're putting the top motor housing back on the unit, make sure that the brush speed selector knob that's on the right side of the turbine fits through the **** in the top motor housing. Also before tighting the two screws that that hold the top housing in in front of the brushes, there's two clips. You'll need to snap the top motor housing behind these two clips. Simply push front of the motor housing until you hear it snap into place.
\015\012
\015\012That's about it. If you have any trouble with this repair, please don't hesitate to use the Clarification request form here on Fixya. I'm always more then happy to answer any follow up questions that you might have. If this repair was helpful to you, please help other Fixya members with this same problem find my repair by rating it helpful. You can do this by clicking the 4 Thumbs up icons in the right hand corner.
\015\012
\015\012Thank you very much,
\015\012
\015\012Chris J.
\015\012GoVacuum
Repair Help & Product Troubleshooting for Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover steam vac all terrain turbine gear assembly


Hello,\015\012\015\012I'd be happy to walk you through this repair. Unfortunately this is a very common problem with the Hoover SteamVacs. \015\012\015\012Here's what you'll need to complete this repair:\015\012- ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover Steam Vac Dual VModel #F7430-900 the turbine does not turn


... Hoover F7220900 SteamVac V2 Upright Vacuum

How do you remove hood on a f7425 hoover steam vac


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

How do you remove hood on a f7425 hoover steam vac


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Valve Stem Assembly for Hoover Steam Vac


Put the rubber seal on the bucket first, then put the spring on the valve stem, slip into the hard collar, then push it into the opening in the seal, it will snap into place. ... Vacuums

Turbine Hi I found out through your site that my turbin is bad on my steam vac and I found some information as well on how to disasemble the steam vac to get to the turbine but still was wondering if there were some more detailed instructions on how to remove the turbin. I am a sigle mom and doing the work on the steam vac myself and need a little more detailed instructions. Please help asap and have a bless day.


There are some screws on the bottom that have to come out so you can remove the top housing. Take the brush block out, there are 2 screws above where it sits. The turbine sits near the front, and in the mid section, 2 screws on the front of it and 2 ... Hoover F7220900 SteamVac V2 Upright Vacuum

How do I replace the pump assembly on my Hoover steam vac model f5835-900


Easy just remove the case andtake out the pump then do the reverse in the same order. ... Hoover Vacuums

Is there a diagram showing hor to teomve turbine from 7452 hoover steam vac


... Hoover F7452-900 SteamVac Upright Vacuum

Hoover steam-vac model #F7458-900 "All-Terrain"


Check the valves at the bottom of the tank(43513026)also check for cracks in the tank(42272104). Another thing to check is the handle asm. is a rod that pushs on the resevoir asm(tanks sits on) to make sure that it is stuck in the on pos ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

How to replace the pump assembly on hoover steam vac


Go to http://hoover.com/support/video-instruction-guides/ see the troubleshooitn guide . Proceed with common sense.Go to see the video attached for change pump hooverGod bless you ... Vacuums

We are putting our Hoover steam vac F7425-900 back together again after getting a new turbine assmbly part. However, we have a part ( #38454-013) that we are unsure where it fits. Can you assist us?


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover Steam Vac Dual Tank Bottom Valve Spring Assembly Part Needed


It appears that there is a problem with the o-ring design. The o-ring should maintain a certain OD dimension and keep the spring assembly from pulling throught the hole. I am trying to find the service manual to locate the o-ring part number but hav ... Hoover F7431-900 SteamVac Vacuum

Where does the pump assembly go on hoover steam vac?


See the video attached: ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover steam vac ls brushes wont turn how to clean turbine


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Help!!! I bought a replacement nozzle valve for a hoover steam vac hose and I can't get it back in right. Does anyone know where I can find an illustration of this assembly??


Hessco.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.


... Vacuums

I need a diagram to install a turbine in a hoover steam vac model f7425-900


If you give me your name, address, city, state and zip code\015\012I can send it to you in the mail. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a Hoover steam vac Model #F5865-900. I am unable to have the cleaning mode change from tools to floor when lowering the handle release. I hear a click, but the indicator stays on tool. I need to know how to get to the assembly that controls the cleaning mode.


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Replace a turbine and gear assembly on a hoover F5914-900


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Hoover steam vac F7427-900, brushes stopped


This is not correct, the turbine bearings are NOT sold separately. Hoover only sells the entire turbine gear assembly complete, not in separate parts. \015\012\015\012To verify this, please see the parts diagram below, you'll see that ... Vacuums

Hoover steam vac model f5857-900 manual - Hoover Steam Vac Carpet Cleaner Spinscrub F59149RM


... Hoover Steam Vac Carpet Cleaner Spinscrub F59149RM

No suction on hoover steam vac F5871-900 - Hoover Steam Vac Dual V w/ SpinScrub Vacuum


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I don't know how to use my hoover steam vac on carpets, hard wood floor, my (tile floor), my upholstery. I'm spraying and yet I don't see no suctions on neither of them. do you have a how to do step by step video that I can use in order to get the maximum result from my hoover steam vac.


Here is a link to the User Manual, in case that will hekp:\015\012\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover steam vac won't heat - Hoover Steam Vac Dual V w/ SpinScrub Vacuum


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0590 seconds