Having problems with your Hoover F5906-900 Upright Steam Vacuum ?

Where does other end of hose go

\015 I have a hoover steam vac model F5915-900.I placed one end of hose into recovery tank as manual illustrates. manual does not illustrate where other end of hose goes. I turn on vacuum and it sucks are through hose. assume it should be sucking air through portion of steamvac that is in contact with carpet.inspection of steamvac reveals no aperture or connecting port for other end of hose.I feel intense rage toward hoover.\015

Answers :

You're quite right . . . the manual doesn't show where the other end of the hose goes, which frustrated me as well. I finally found another pic of the cleaner (I think it may have been the one on the box) which revealed the answer. If you're facing the rear of the machine, there is a plastic "hose clip" on the right side of the machine (it looks like the letter "c"), and the "loose end" of the hose is snapped into place in that holder - it doesn't actually connect into an aperture (that end of the hose is just to place the little furniture brush on, if you use it). Once in place, the hose will actually kind of overlap itself and be held firmly in place against the side of the machine. Hope that helps - I too am not a fan of manuals that leave obvious questions unanswered.
Repair Help & Product Troubleshooting for Hoover F5906-900 Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dyson DC07. The hose has come away from the hose end and the end is stuck in the top end of the wand as it sits in the upright position on the machine. Any ideas as how to get it out? If I can get it out it might just be a new hose. If not, it's a new hose and wand.t


... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!


Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

I have some sort of object in the hose of my Epic 6500. I have tried reversing the hose and blowing out the foreighn piece of debeis but this has not worked. Is there a way to remove the plastic connector end to access this end of the hose? Or is there another solution to this problem?


By reversing it, I assume you plugged the hose into the exhaust blower on the top of the machine. If so, insert the other end into the intake and turn one the vacuum. This way the clog is also getting sucked at what should be the loose end.\0 ... Electrolux Epic 6500 Vacuum

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss


Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

How to replace just the Kirby 210097 Hose End For G5 Series Vacuum Cleaner to hose. can buy replacement but can not get the broken end off


Simple and rquires no tools. Fill your sink with hot water and set the end in water with attachment on it. Within a few minutes the end is soft enough to slip out. setting the hose end in the water again will let you simply slip the hose into the ... Kirby G5 Bagged Upright Vacuum

Very end of hose on kenmore 116.35923 upright has broken and attachments won't stay on. need new hose or a way to fix the end of this one.


... Kenmore Vacuums

How can i put on the snap ring on an eloctolux vacuum hose on the end piece of the hose; it is a swivel end and an older vacuum cleaner plastic canister type


The snap ring is generally found on a Canadian made LUX AP series prior to 1982 and it is in fact a coil spring you must leave the wiring off the handle. Be sure the steel cap and rubber o ring are on the tip of the hose. Slide the handle onto the ho ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.


You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum

Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.


Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum

Hose Problem The hose broke just above the cuff on the inlet end of the hose.  I found that the hose doesn't thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?


Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in. ... Eureka Sanitaire SC4570 Bagged Upright Vacuum

My electrolux 2100 vacuum hose broke. I replaced the hose but now I dop not have power at the hose end. is there a curcuit breaker in the canister tha supplies power to the hose??


... Electrolux Guardian Bagged Canister Vacuum

Clogged hose... I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you


Hi!\015\012 \015\012Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Con ... Bissell 6594 PowerForce Bagless Upright Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!


Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

There is a cut at the end of the hose. Is there a way to cut the hose at the split and reattach it to the connection? Thanks.


Unfortunatly the amswer is no you will have to replace the whole part. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The hose is clogged in my Kenmore progressive 116.28614 vacuum. The clog is near the end of the hose -- towards the bags but below the elbow in the hose. How can I unclog it?


... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Kenmoore Intellivac w direct drive suddenly started making internal sound like something was stuck. Hose is clear, and sound is made when hose is detached from main unit. Vacuum sounds find at lower pressure, only makes sound with bag door closed and/or placing my hand over the end of hose.


Shut off the vac and open container and remove the bag. Try dropping a coin into the hose, then raise up to see if it falls thru to the bag area. If it does check the throat of the vac where the dirt is sucked upward to dump into the bag itself. ... Kenmore 35912 / 35913 Progressive Upright Vacuum

My BROAN CV-110 hose with the rug beater only works if I turn it on from the base unit. Shouldn't it turn on when I plug the hose into the wall recepticle? Do I need to replace the hardware at the end of this hose and if so, where would I purchase that? This central vac came in a house I just purchased. Thanks for any help. Sherry


... Broan-NuTone CV450 Central Bagged Central System Vacuum

I have a Hoover windtunnel T series. Model #UH70105. The system check indicator was almost red so I cleaned the filter. There are no clogs and it vacuums fine without the hose, but when I go to use the hose there is very little suction and all the vacuum dust flys out of the end the hose piece fits into when not in use. Can you please tell me what is wrong?


... Hoover Vacuums

Where does other end of hose go


You're quite right . . . the manual doesn't show where the other end of the hose goes, which frustrated me as well. I finally found another pic of the cleaner (I think it may have been the one on the box) which revealed the answer. If you're facing ... Hoover F5906-900 Upright Steam Vacuum

REMOVING HOSE END


I had to replace the hose end on my Kirby, the motor end. I have the Diamond edition. Just take a hair dryer and get the end of the hose warm, and then us a screw driver. Works like a charm. It stays warm long enough to put the new end on. ... Kirby G6 Bagged Upright Vacuum

Im in need of the two solid hoses and hard floor end from a kirby g series ultimate , can you help, both my solid hoses have cracked and fall out all the time, cheers Carole


Two words Ebay or Amazon. ... Vacuums

Kenmore progressive vacuum model: 116.25614506, I replaced the bag and filter and now it seems to **** the bag up against the hose outlet with very little suction at the hose end


... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Low suction at end of 30' hose, after I snaked the hose


Snaking the hose won't change the suction unless you pushed an obstruction deeper into it. Try dropping a coin through the handle and shake it through to the other end. If the coin stops it will rattle at the obstruction. If the coin passes through y ... Broan-NuTone Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0286 seconds