Having problems with your Hoover F5906-900 Upright Steam Vacuum ?

The spinscrub brushes won't spin when any pressure is applied to the machine. What is the reason for this?


Answers :

There is an air inlet screen behind the brush indicator....if this is plugged with hair and debris, this will cause the brushes to stop spinning....also, if the mackine is upright or if the recovery tank is not in place, then the brushes will not spin.
Garyboone is right on!! That is the solution (I did it and it worked)
Repair Help & Product Troubleshooting for Hoover F5906-900 Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The spinscrub brushes won't spin when any pressure is applied to the machine. What is the reason for this?


There is an air inlet screen behind the brush indicator....if this is plugged with hair and debris, this will cause the brushes to stop spinning....also, if the mackine is upright or if the recovery tank is not in place, then the brushes will not spi ... Hoover F5906-900 Upright Steam Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand


In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 


For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum

Brushes on my hoover spinscrub model F7411900 wont spin


Vanger cheva in post 1 got the correct answer. I just disassembled my f7411900 with some difficulty and took the turbine apart. Sure enough the bearing on the shaft was froze from rust. I was able to free it up in a vice and screw driver big enough t ... Hoover Vacuums

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes will not spin when in the lock down position. I adjusted the arm internally and it does not seem to apply enough pressure to have it fully lock down. Can the mechanisms wear out.


This unit has a rubber "clutch" piece to engage the brush which must be replaced occasionally. See if you can move the brush with your fingers while holding the belt to prevent it from turning - be sure the switch is set to carpet, and the motor is o ... Riccar 8955 Upright Vacuum

Brushes spin slowly then when applied pressure they stop


Steam Vac has no adjustments. Solution: Remove the clear plastic cover located in front of the brush control switch (I used a butter knife). Locate the small screen and remove the dirt and hair from it with your fingernail or an old tooth brush. R ... Hoover F5906-900 Upright Steam Vacuum

Have a spin scrub a couple of years old. Have used it maybe 5-6 times and the green brushes only spin if you take the tanks off and set the machine upside down and push the brushes toward the machine... the second you stand the machine up they quit spinning.


Repace the belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My dyson dc animal's brush is not spinning. The machine smells like burning rubber. I believe the clutch has gone out but the machine also only sucks from the top of the hose in the handle. I am wondering if the machine is not locking properly which is causing the brush to not need to spin. If this is the problem how do i fix this problem.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate


If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

Brushes won't spin on a Hoover Steamvac SpinScrub Model F5918-900


Well the hand tool works off the suction of the machine and has nothing to do with the turbine that controls the brushes. if you can get the part i can walk you through taking it apart. when you write back, let me know what the model num of your mach ... Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Agitator brush wont spin once vacuum is placed on floor


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=618889&thid=573865\015\012Agitator brush wont spin once vacuum is placed on...\015\012Posted by coral7980 on May 05, 2008\015\01 ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The brushes on my Hoover Steamvac Widepath LS SpinScrub model # F6040 900 are not spinning. What should I do to get the brushes spinning again?


On those models the brushes are turned by suction. 1. Check the lower tank to be sure its completely closed and sealed.2. Check the lower tank to be sure the tools filler plate is in place (if you used the tools recently)3. If both 1& ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The flexible brush on my unit does not spin. It did 'by accident' pick up a cat poo that didnt make the litter tray while I was out, (and it happily spread it all over the house and skirting boards). I cleaned the unit, removed the base and wiped everything clean. I've unscrewed the flexible brush and cleaned underneath it but it still wont spin. Any suggestions?


... iRobot Roomba 530 Robotic Vacuum

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

My vacuum's cyclonic action is not spinning and creating very little vacuum pressure through hose or floor brush area. I already checked, brushes are spinning, there is no apparent blockage in the canister, I took it completely apart and removed excess dust from the filter. Still no good vacuum. Any suggestions?


The following filter in your in your dump cup needs to be replaced. \015\012F24 Dirt Devil "I" Bagless Upright Vacuum Replacement Filter Style F24 ... Dirt Devil M130005 Bagless Upright Cyclonic Vacuum

My hoover spin brush steam vac brushes wont spin


Unplug vac turn it over and check for belts that drive the brushesThey are located at the very end of the brush They are probably missingor they snapped and sitting in the housing somewhere. If you ar mechanically inclined not very difficult ... Hoover Vacuums

DC07 brush wont spin on bottom, took all apart and wont work


Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brushes not spinning or barely spinning while operating machine


There are filters, one on the lid, the other from the bottom, has a red frame, pull it out and clean it. There maybe a foam filter on the lid covering the yellow ball, it needs to have at least a 1/4 in. gap from the top. Also make sure that the li ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes will not spin while locked in machine..


\015\012\015\012I have the same problem and think I know the solution.\015\012The plastic pegs on the housing unit for the brushes have been stripped out. The pegs are supposed to be squared tip to click into the square hole of the machi ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover steamvac Spinscrub F7222-900 brushes do not engage. Brushes will spin when unit is laid down and the brushes are pushed upward, forcing the male brush linkage into the female receptacle , but when the unit is stood up it disengages. Turning the switch on and off does not make a difference.


That's the way it's supposed to work. ... Vacuums

THE BRUSH WONT SPIN AND THE SOLUTION WONT COME OUT


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0888 seconds