Having problems with your Hoover F6020-900 SteamVac Upright Vacuum ?

Broken Upholstery hose on my Hoover SteamVac Model #F6020. How do I remove the old hose to replace it?


Answers :

Repair Help & Product Troubleshooting for Hoover F6020-900 SteamVac Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Broken Upholstery hose on my Hoover SteamVac Model #F6020. How do I remove the old hose to replace it?


... Hoover F6020-900 SteamVac Upright Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

I have a Hoover 5899-100 Steamvac. The hose is cracked at the bottom. I am going to order a replacement hose, but can't figure out how to remove the old hose. are there instructions out there to do this.


... Vacuums

Hoover, model # UH30070 Wind tunnel vacuum Brush won't turn. I do not see how to remove this to replace the brush, and besides it's only about a year old! Why is it already broken? There's no visible evidence on the brush that would make it stop, i.e. string, clogged, etc. Can you help?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

I have a Hoover SteamVac spot cleaner, model F5505. This is an older cleaner. It has no suction and I believe the hose may be clogged, but don't know how to remove the hose and check it.


... Hoover F5505 SteamVac Spot Vacuum

I have hoover steamvac models f5889-900 and f7222-900. The brush motor is broken in model f7222-900 and I replace with working motor in f5889-900? I am using f5889-900 just as parts


... Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks


Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

The hose has a hole in it and the red ball keep shutting it off. Model F581-900 I have another Hoover SteamVac that is broken too. Where can I get these fixed, I live in Crown Point, IN. Thanks Valerie


I think all of the Hoover Stores are out of business.\015\012\015\012Try here for parts\015\012\015\012 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Windtunnel T-Series UH20700 9 mos old. Keeps clogging in hose just above the beater brush assembly. I think it clogs because the suction is too weak to pull much through. Primary filter is clean and HEPA filter is replaced. Even when everything is unclogged, suction is weak compared to another unit (same model) that a friend has. Any ideas?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?


Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Need replacement hose for Model 704, Peak 1.7hp Montgomery Ward by Hoover canister vacuum. 7.4 Amps. It's 25+ years old.


Hello Sir.\015\012Welcome To Fixya Community.\015\012I am Glad to Help You.\015\012\015\012You can check out these pages for your specific model.\015\012\015\012 ... Vacuums

Hoover steamvac ls edition, model f5894


... Hoover F5807 SteamVac Wet/Dry Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks


If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Lower hose broken hoover agility how to replace


To replace a hose on the Hoover V2 is a pain in the you know what. i would recommend 1. take it in and have a professional repair shop do it.2. trade the V2 in for the Hoover PowerMax steam cleaner with spinscrub they are 10 ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Hoover Alyx Pets 2000w Hoover Model TC1208 001 Virtually no suction, have checked for blockages but cant seem to see any, however i can't remove the hose to check it. Any ideas?


Did you check the HEPA filter? I have the same problem with mine if I don't clean the filter after using it. It's a dirty job but helps for a while. ... Vacuums

The belt is broken on our Hoover Allergen Filtration Model U5018-900 120 v. 60 Hz 12.0 A. Belt 38528040. Where can I get the belt and instructions on how to replace the broken belt?


The owner's manual can be downloaded here (in red, "Download the Instruction Manual (PDF))\015\012http://www.hoover.com/product.aspx?model=U501 ... Hoover U5018-900 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1313 seconds