Having problems with your Hoover F6207-900 Steam Cleaner ?

Brushes stopped working - Hoover F6207-900 Steam Cleaner


Answers :

(1) Assure the Brush Control on the hood is NOT set to the OFF position.
\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.
\015\012(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
\015\012(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
Repair Help & Product Troubleshooting for Hoover F6207-900 Steam Cleaner

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes stopped working - Hoover F6207-900 Steam Cleaner


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F6207-900 Steam Cleaner

My Hoover Steam Vac Ve brushes stop working - Hoover F7431-900 SteamVac Vacuum


Hi There,\015\012\015\012You'll need to try and diagnosis what is causing the brushes to stop spinning first. A lot of the times this can just be caused by debris stuck in the brushes. I have written a in-depth repair solution on how ... Hoover F7431-900 SteamVac Vacuum

My hoover carpet cleaner has stopped pumping water out it is a hoover brush n wash but it isnt a steam vac


... Hoover Vacuums

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

I purchased a hoover windtunnel 2 model#u8361900 in Dec 2007.I am very disappointed because the self cleaning filter is not turning and particles keep clogging in that area. I have manually removed the particles but the filter will not turn.I also haven't been able to use the pet brush for some time.The cleaner has not been used hard about once a week since it was purchased.I am not happy that this product has stopped working effiently since purchased 6 months ago. Thank you Marcia Long Pottstow


The filter stands up right.the bottom goes in first then snap in the top.turn it by hand and you should hear it click if you have it in right ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a 3 or 4 year old Hoover steam carpet cleaner: model # F 5857-900  It stopped working and does not vacuum up liquids or dispense liquids for the water container. Where can I take it for repair? I live in Colchester,CT 06415. Also,is there any written repair manual that my husband might be able to use?


... Vacuums

Suction Problem I just borrowed the Hoover Steam Vac Deluxe w/ 5 brush agitator from my neighbor and it worked ok for the first few minutes, although the suction would stop and go. When I had enough water to dump I did it and when I put it back on it no longer sucked the water up from the carpet. She admits to having it for 15 years, but why did it have to break on me. Makes me look as though I did it!


Check and make sure the dirt water tank is properly on if it it is chech inside the lide to make sure the red stopper is not stuck to the top this will cut off the suction ... Hoover F7431-900 SteamVac Vacuum

My scrub brushes quit working on modelf5915-900 in less than one year this is my second machine in 3 years. Now I'm very angry with hoover company. Can this be fixed and how much will it cost me? Steam cleaners


There are a couple of possibilities: the first and most simple fix would be to replace the brush-block, which simply releases from the bottom by pushing the retaining tabs free. If you pull this out and attempt to spin the brushes by spinning the gre ... Hoover Vacuums

My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.


... Hoover F5826-900 SteamVac Upright Wet Washer

NoSuckage !!! It seems as though my hoover steam vac has stopped sucking up the water. It is still spraying the cleaner correstly though, just won't suck it back up. I've emptied it several times and it was working properly up until a few minutes ago. HELP !!! Family coming in town tommorrow !!


I had borrowed a friend's steamvac due to potty training problems with my puppy. Today it stopped sucking up the water and I completely panicked! Immediately I googled hoover f5866-900 trying to find a replacement before I had to return the vac to my ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover nanolite power brush stopped working


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

BRUSHES WONT TURN ON HOOVER STEAM CLEANER - Hoover F5891-900 Steam Cleaner


Belt probably broken. unplug from power and remove the plate from the bottom of cleaner.belt should be visible on one side or other. ... Hoover F5891-900 Steam Cleaner

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch


... Hoover Vacuums

MY WIFE BOUGHT THIS FOR ME FOR FATHERS DAY GIFT ABOUT ALMOST 2 YEARS NOW OR SO,BUT I HAVE THIS PROBLEM THAT THE BRUSH DOS'NT SPIN ANYMORE EVERYTIME I PUT THE SWITCH ON FOR BRUSH ON,THE HOSES BRUSH SPIN IS WORKING BUT FOR THE FLOOR CARPET BRUSH SPIN IS NOT WORKING,AND THIS IS THE MODEL NUMBER OF MY HOOVER VACUUM CARPET SHAMPOO CLEANER IT'S F7411-900


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

I have a new Hoover Dual V steam vac that I bought from a neighbor who only used it once. I have only used it once since then and it worked great. This time, because I am pregnant, I bought some non-toxic cleaner that was much thicker than the very watery Hoover soap. This vac has a wash option and a rinse option. The rinse option works (sprays and sucks properly), but the wash cycle doesn't at all-neither soap nor water comes out. Nothing comes out, but it still sucks. I took everything o


There's a powerful electric motor attached to a fan that sucks in air.Did you checked and cleaned that motor.If the dirt is got stuck up ion the motor then the motor will not spin as per its regular speed.For rinsing the motor spin on one cycl ... Vacuums

My Shark Steam Cleaner has stopped heating water to make steam, how do I repair this? This is an older model and no longer under warranty, but when it was working it was GREAT and I want it to work again.


... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

Hoover steam vac F7427-900, brushes stopped


This is not correct, the turbine bearings are NOT sold separately. Hoover only sells the entire turbine gear assembly complete, not in separate parts. \015\012\015\012To verify this, please see the parts diagram below, you'll see that ... Vacuums

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.


You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover F7431-900 steam vac brushes wont work


The brushes are activated by suction, my berings and gears froze up, i took it apart, kinda hard to figure out, but not as bad as it looks. i lubed the berings and the gears, then i took an air compressor to the activation fins and let it spin, lubed ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes Hoover steam vac f5906-900 .can,t get the brushes to work. Is there a belt that could have broke


This machine has no belts. There is an air driven turbine that propels the brushes. If you look under the little glass window at the left front corner of the machine, there is an intake screen just above the indicator dial. That screen is there to ke ... Hoover F5906-900 Upright Steam Vacuum

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1355 seconds