Having problems with your Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum ?
The plastic cover that suctions the water is cracked
This is a fairly common problem, the nozzle gets cracked from bumping into corners and wals and stuff. part number 37275069 available at sears 1-800-4myhome. i'm not pushing sears, it's just easier for most folks to order themselves
Repair Help & Product Troubleshooting for Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The plastic cover that suctions the water is cracked
This is a fairly common problem, the nozzle gets cracked from bumping into corners and wals and stuff. part number 37275069 available at sears 1-800-4myhome. i'm not pushing sears, it's just easier for most folks to order themselves ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl
There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums
Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),
Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum
I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from
... Bissell Vacuums
We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?
Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums
I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke
Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums
No Suction The water/soap solution dispensing just fine but when I pull the machine back over the water solution, it is not being sucked up (usually it is easy to see as it you can see the water being pulled up through the clear plastic)
It sounds like the lint filter is clogged. It is located on the top clear plastic piece (the one with the dial to switch from floor to tool use) and is on the underside. It is a small (1 inch square) red plastic piece with a little door on it. Fli ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I bought a fantom vacuum on HSN about 9 years ago.Whan it was delivered the first one was broken so they sent a second one.tThat one also was cracked on covering for brush. I called and they told me they were no longer available,so I kept that one,since it would cost me shipping to return.The back right side wheel evenually cracked and fell off.I was able to put it back on and it would stay for a few weeks or so.It now has a large piece of plastic that has broken off the wheel where the bolt fit
My machine wont pick up the dirty water. If I take the cover off the recovery tank there is a lot of suction but it wont **** up the water. my carpet is soaked. What can I do
At power head clean out area before power head also look for small hose and clean out and look at rollers,i hope this works if you have directions still they should be able to help you out some more.thanks ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I bought a Dyson Vaccum for pets. Spent around 700 for it, and thought it was the cats meow. They promise that there is no lose of suction, and oh boy is that a joke. I clean the filter that they say they don't have, which they do. I have cleaned it up thinking I just have a dirty vaccum. Now the hose sucks together so hard that it is pretty flat. And the plug in is EXTREMELY HOT!!! It seems like the littlest things fall off of it, and it is all plastic and it cracks and pieces break off.f I don
Sure, we have Miele machines that are German made and excellent with 10 year warranties we are also a dyson repair center for warranty.\015\012Dyson Repair Form ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I need a lid (cover) replacement for my rival slow cooker model scv551. The plastic lifting piece has cracked.
I need a replacement cover for my Rival Slow Cooker size 3.5 quart Model 3730. Where can I get it? ... Vacuums
I vacummed some sheetrock duct up with my hoover elite cyclonic.. i dumped the canister to empty the dirt and dust, but now theres not as much suction... is there any other area I should be cleaning... or can i submerse the plastic filter part in water?
Do not put the filter in water, it will ruin it. if banging out the filter did not work than you should probably replace it, sheet rock dust is very fine and will easily clog most filters. ... Vacuums
Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken - the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can't find one anywhere. Anyone know what I can do? thanks
The exact same thing happened to me. i just called and ordered it from eureka. the number is 1-800-282-2886. the cover cost 13.07 and the s ... Eureka 2576A Steam Vacuum
Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.
... Hoover Vacuums
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums
On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums
No suction to retrieve water from carpet
The tank lid of your recovery tank is designed to engage two tabs to lock the front of the lid down on the seals. Look at the front corners of your recovery tank. You will see a tab extending out on each corner. These two tabs insert into the corresp ... Vacuums
The water dispenser must have been left plugged in and the hot water switch on without any water bottle on the unit because a plastic part inside got warped and now the unit tries to heat the whole 5 gallon jug of water. I want to replace the inside plastic part but I don't have the manual and don't know which part no. to request or where to send my request for parts.
Please state the brand and model number of your water dispenser, so I could give you the exact part and lead you where to purchase it.Post back ... Vacuums
My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.
Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a hand held vaporettino steam cleaner ....the appliance is working but the water container has been dropped and has a hair line crack in the base and leaks the water from the crack ....I am looking to either buy a replacement water container or to buy a new S/Cleaner if you could let me know of a supplier either in the UK or Spain
... Polti Vacuums
I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?
Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums
The suction on my Hoover Spin Scrub 50 is suddenly not working. This is the 2nd or 3rd time I've used it and until now it has done a great job. But now it leaves my carpets soaking wet with no hope of drying and no dirty water is being suctioned into the dirty water tank. Help!
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Water won't spay out of the nozzels under front plastic
There are 6 screw, 3 on each side, then the top will come off. When you put it back on, make sure the piston is attached to the bottom of the smart mix knob and that the knob is in the water setting.\015\012\015\012 ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!
There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum