Having problems with your Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum ?

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),


Answers :

Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong enough to pull anything up, but you may have a problem witrh it not seating all of the way on both sides, and you ,maynot feel much there anyways. Check at the bottom where the tank sits. is the seal ok. With the tank off, is there alot of suction at the filter screen? If there is, then the problem wouldn't be inside. Is the hose door on the back closed tightly? How old is this unit, if less then a year, then it is under warranty. There is an automatic shutoff for suction when it senses that the tank is full, maybe the problem is there. I believe it is the float inside the tank.
Repair Help & Product Troubleshooting for Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),


Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

Upright self propelled Windtunnel model: The self propulsion does not work and I can see why. I need to know how to get the top cover off the machine to get to the broken part that engages and disengages the wheels. Can you tell me how to get the cover off?


Turn the machine upside down and locate about half a dozen recessed screws which hold the bottom and the top of the machine together. ... Hoover Vacuums

On my DC17, the wand is not working right. The upright part works fine, but when I go to use the wand, the hose sucks in on itself. I get suction for a few seconds, then the hose collapses in on itself and no more suction.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?


The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan


I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

No suction hello, there was a rubber smell then no suction. i'm thinking it needs a new belt but don't know how to remove the cover to replace. is it a complicated procedure. is there a diagram available? don't have any info here. thanks, leslie


Flip the machine upside down and remove the four screws from the baseplate. Replacement should be fairly self-explanatory from there. If it's a self-propel model, note that the v-belt in the front WILL look loose normally, so it does not usually requ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My dyson dc07 animal bagless upright cyclonic is giving me problems with the bottom part where it sucks up the dirt the part that covers the brushes is not going on like it suppose to what am i doing wrong


CKECK Clutch Assy and belt\015\012bottom part where it sucks \015\0121: try us WD40... \015\0122: Replaced power switch Part No : 910971-01 ... Vacuums

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

I just recived a free Kirby G3 vacuume. the only problem is the on/off switch dosen't work and someone took it apart before i got it. all of the parts are there as far as i can see but they did not label the wires I need a diagram to be sure that i replace them correctly. Where can I find one?


... Kirby Generation 3 Bagged Upright Vacuum

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

While cleaning, the vacuum sucked up a nail and I suspect it may have punnctured the hose from the vacuum base to the uppper cannister. The reason is that it appears to have lost its suction power and nothing gets into the fliter cnnister area any more. How do I replace this part ?z?


You will have to basically split the vaccume in half to gain access pulling the plastic covers off.usually philips head screw/ ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.


Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I am looking for an instruction manual for a Sieger Titan Cyclone Vacuum Cleaner Model CVC-H6101-GAU. I think some parts have been lost from our vacuum cleaner but I can't tell without a clear picture or exploded diagram of the unit. Norm


... Vacuums

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks


Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums

My kenmore hida filter vacuum cleaner no longer has the sucking ability it used to have. It is only 4 years old and has worked extremely well up until this week. The motor is functioning well, as is the carpet brush function.... it just has a very weak suction... Is there any easy way to tell if it is blocked? An ideas of what is going on? thanks


Well i've hade one come in a while ago and it didn't have good suction so I looked at the bag it was buljing w/ dirt so I put a new bag in it and it had better sucktion but still not good enough so I cheched the fabrick filter and it was dirty too so ... Kenmore Whispertone 23312 Bagged Canister Vacuum

No suction vacuum won't pick up -- I've checked the bag, hose...and it seems to have no sucking power. The internal hose may be jammed (I vacuumed up a lot of shredded paper), but nothing as far as I can stick in fingers in. I don't have a metal coat hanger to slip down, but I'm afraid that might tear the hose and then the darn thing won't work anyway. :o(


If it is plugged, try using a tape measure, i know it sounds stupid but it will work to unplug your line and will not tear your hose.. ... Kirby G4 Bagged Upright Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

PROBLEM I HAVE CLEANED PART OF MY CARPET, BUT WHAT SUCKS UP THE DIRT OR WATER AS CARPET WAS WET, I HAVE WATCHED A VIDEO, BUT DIDN'T GO FAR ENOUGH TO EXPLAIN THIS, AND WHAT DOES THE BELT DO THAT IS LOOSE FITTING IN BETWEEN EACH SIDE OF BRUSH. KINDEST REGARDS


A Shop vac is my usual solution to my crappy Kirby shampooer.. ... Kirby Heritage II Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.


The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

Not sucking up through bottom but plenty suction on tools part


... Dyson Vacuums

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0601 seconds