Having problems with your Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum ?

Split hose? My machine has stopped suction on the main unit. When I tilt the neck all the way back, the hose is split around its diameter. Is there a straightforward way to fix this AND where can I order th part?


Answers :

This piece is available but is very difficult to install. the upper handle needs to be split to reach the upper part of this hose. i would call the manufactuer and find a local warranty service center to get this part.
Repair Help & Product Troubleshooting for Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Split hose? My machine has stopped suction on the main unit. When I tilt the neck all the way back, the hose is split around its diameter. Is there a straightforward way to fix this AND where can I order th part?


This piece is available but is very difficult to install. the upper handle needs to be split to reach the upper part of this hose. i would call the manufactuer and find a local warranty service center to get this part. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Hi I have an Electrolux Envirosteamer and it has stopped steaming. I have made sure the water cap is on tight and also taken the head apart (where the hose finishes up and the attachments fit on) and the hose is intact there. I have no steam and wonder if I have a valve problem? if so can anyone tell me if it's worth trying to order the part and fix myself. I'm fairly handy! Thanks Sue


If the water is boiling and element is ok then it could be the outlet valve it is poss to diy but is a 2 person job as very fiddley ... Eureka Deluxe Enviro Steamer Vacuum

No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All


Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

There is a cut at the end of the hose. Is there a way to cut the hose at the split and reattach it to the connection? Thanks.


Unfortunatly the amswer is no you will have to replace the whole part. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live


... Vacuums

I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.


... Kenmore EVO All Surface Floor Cleaner Vacuum

Hose The intake hose has torn apart at the base where it is attached. Is there some way I can repair it or do I have to order a new hose. The Sears store where I purchased it is of no help.


You will have to replace the hose. If you want to get it thru Sears, go to Sears.com, click on parts, enter the model number, if they have it in their system, you can find the part there and order it. Or take the model number and go to where someon ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.


Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

I have the Eureka Whirlwind upright vacuum. All of a sudden there is no suction- the hose has suction but not main part. I have no idea- but the brush part is not turning??? should I get a new vacuum or is this an easy fix? thanks!!!!!


If the belt isn't turning then it has snapped. Check the top of the hood for two or three crosshead screws; two at the front and one under neath by the left hand side if looking at the upright from the front. Its easy to fix if you take your ti ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

Very end of hose on kenmore 116.35923 upright has broken and attachments won't stay on. need new hose or a way to fix the end of this one.


... Kenmore Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

How do i fix the retractable cord on a dyson dc08 to go in all the way and not only part way?


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

The hose split. I ordered a replacement but can't figure out how to remove or loosen the back panel to get the old hose out and the new one in.


Hello,\015\012\015\012I'm sorry, I thought I had one of these models in stock here so I could take it out of the box and photograph this repair for you. Unfortunately I didn't have the exact same model, however I do have a similar model ... Eureka Smartvac 4870 Bagged Upright Vacuum

Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of


Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums

Maytag F6212-901 suction hose split


... Vacuums

I bout this vacume in mid December 07 and about February-March it started not picking up the dust on the floor. So in early April I bout a new filter and it still wasn't picking up the way it had in the beginning. I've taken it a part several times and cleaned it out with it being plugged at the bottom hose with dust bunnies. Well I just took it back to Walmart where I purchased it and I failed to keep the reciet they could not do any thing about the sweeper. I went back to the sweepers and re


Pull the hose out of the holder, is there suction there. If not, then there is a clog in the hose. If there is suction, then check the dirt outlet by the brush roll. Also if the belt is slipping, it may appear to not have as much suction, belts wi ... Dirt Devil Vacuums

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Can I get a replacement hose for an older model vacuum? Model VNB-7 canister? Just guessing I would say yes. How and where do I order this part? I have probably had this unit for 20 + years! [email protected]


... Metropolitan Vacuum Company Metro Vacuum Magic Air Deluxe 4.0 Peak HP Inflator/Deflator Vacuum

I have a euro-pro vapor stream cleaner Model EP95. The rubber sleave inside the canister that connects to the hose is split. Can it I buy a replacement part?


... Euro-Pro Steam Cleaner EP95 Canister Vacuum

My Panasonic model MC-V6830 works but no suction. I checked and belt was loose, but there is nothing to attach the back of the belt onto. Seems some screws or plastic pully part/parts are missing. What parts do I need to order to fix this vacuum?


... Panasonic Vacuums

Attachments The hose attachment doesn't spray out water. it seems like the trigger doesn't pull back enough. Is there something I can do to fix this or do I need to get a new part?


Most likely will have to replace either the nozzle valve or the hose comes complete, so if the nozzle pieces are available, then replace the complete hose asm. ... Hoover V1 SteamVac SpinScrub Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0758 seconds