Having problems with your Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum ?

Water attachment hose

\015 Leaking where attachment hose connects into Steamvac\015

Answers :

Repair Help & Product Troubleshooting for Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Rainbow Series E is leaking. Not sure if water is leaking from the water bin (doesn't appear to be cracked/broken). If not the bin, where else might water be leaking from and what are repair options? Have replaced belt on carpet attachment, cleaned the opening where hoses attach to the canister, etc


You need to clean the separator. ... Rainbow E series Canister Wet/Dry Vacuum

Upholstry attachement Hi, I have attached my upholsty hose, but it will not suck up the water. The hose is spraying correctly. Can you help. I have a Hoover SteamVac Supreme. Thank you, Sarah


The hose end should have a duct on it that you insert in front of the dirty water tank. It must be down all of the way so it will seal. This is where your suction starts from. Acouple of other reasons could be the dirty water tank lid is not locke ... Hoover F5832-910 SteamVac Supreme Vacuum

I have a tear in the hose of my old model # F6030-900 unit which doesn.t allow water from the attachment to **** back into dirty water bucket. The model #F6039-900 is the same model # but different year I understand. The tear is at the bottom where set the recovery tank in the lay down position and can look in the unit at the bend of the hose.


You will have to replace the hose asm. You can order online at: \015\012http://vacuumsuperstore.com/F6019.html\015\012\015\012H-90001334 (43 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Pro Heat Pet will spray water but not pick it up when cleaning the carpet. Is there anything I can do to fix it? The furniture attachment hose picks up water well. It seems like it could be a bit more powerful of a draw on water. I don't know it that has something to do with why the floor cleaning sucktion doesn't work. Thank you for your time. Jenn


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bissell Vacuums

Water leaking out bottom with hose attached


The water hose plugs into the solution valve-pressure on the side of the noozle(bottom). There may be a water line that has come loose there, you will have to take the top off to get to it.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.


... Craftsman Vacuums

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o


It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Hi I have an Electrolux Envirosteamer and it has stopped steaming. I have made sure the water cap is on tight and also taken the head apart (where the hose finishes up and the attachments fit on) and the hose is intact there. I have no steam and wonder if I have a valve problem? if so can anyone tell me if it's worth trying to order the part and fix myself. I'm fairly handy! Thanks Sue


If the water is boiling and element is ok then it could be the outlet valve it is poss to diy but is a 2 person job as very fiddley ... Eureka Deluxe Enviro Steamer Vacuum

II have the kirby sentria, i have it in canister mode with blower attachment on the hose is on with the hand sprayer attachment the problem is the foam is not coming out the sprayer used it just fine all day went to refill w/ water and cleaner now the foam wont come out whats wrong with it?


Make sure the "straw" is in.See if dust coming out of the hose did not clog the air passages. ... Kirby Heritage II Vacuum

New 50 pint frigidaire dehumidifier won't drain via attached hose , only collects water in bucket and this is a pain! How is the hose supposed to be connected? Seems strange to just screw it into the back of the unit; am I missing something?


... Vacuums

It won't spray the water on the floor. I check the hose and the water does come through the attachment? What do I do?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Attachments The hose attachment doesn't spray out water. it seems like the trigger doesn't pull back enough. Is there something I can do to fix this or do I need to get a new part?


Most likely will have to replace either the nozzle valve or the hose comes complete, so if the nozzle pieces are available, then replace the complete hose asm. ... Hoover V1 SteamVac SpinScrub Vacuum

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Proheat Turbo puts out too much water and cleaner and won't **** it back up like it should. Also when I use the attachments dirty water runs out the the hose when I am done. It's used a lot, I shampoo all the carpets about 2 times a month and I shampoo the funiture 1 time a month. I bought it about 3 months ago.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

Trigger on hose attachment not working so water sprays constantly


From your description, the trigger sounds like it is stuck in the release position. this sounds like a very simple repair. The component parts need to be looked at by a service shop ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.


May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

I have a Bissel Proheat 2X 12 AMP Model 8920 06242C. It will not squirt water for the floor brushes, or the hose attachment. What could be the problem? Thanx...


Could have a bad pump, also there are solenoids, one of these could be bad.\015\012\015\012 ... Bissell 8910 ProHeat Clear View Upright Vacuum

Cap (top) is froze. Unable to remove cap (top) to pour water inside for use. not sure if model specified is correct. It's a canister with hose and multiple attachments for cleaning.


I too can not figure out how to get the lid off. ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

Is there a -internal- assembly diagram available? Looking for one that shows hose attach info and water flow.


... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

No water comes up the attachment hose when cleaning


Will not pick up water ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I want to use the upholstry attachment and I can't get the water to spray out the hose


Hi\015\012 \015\012 \015\012Before using tool It may be necessary to remove air from the system (“prime the pump”) so the clean solution will flow to the tool. Follow the bell ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

S catch thank you for the pic, i'am pulling like crazy, and this thing is not budging. i will keep trying, but i'am afraid i will break it. i really need to get inside there, it probably is clogged in the heater. it sprays water out of the hose attachment, just not out the bottom. thanks, randy


Look between the 2 fingers there at the top, If I remember there is a catch in between them that you push down to release. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0821 seconds