Having problems with your Hoover F7205900 SteamVac V2 Wet/Dry Vacuum ?

Hoover F7458-900 SteamVac The brushes quit

\015 Hoover F7458-900 SteamVac The brushes quit turning. Why?\015

Answers :

My Hoover F7458-900 was doing the same thing, brushes not turning and since it is about 7 years old and out of warrenty I decided I had nothing to lose so I took it apart after reading all the other posts on this problem. The brushes are actually turned by a turbine motor (no belts involved) that runs off air produced by the vaccum motor of the unit. The air turns a metal spindle that then turns several nylon gears in the turbin the last of which turns the brushes. The nylon gear that engages with the metal spindle was worn down to the point that it was no longer engaging with it and thus not turning.
The only fix for this problem is to buy a new turbin motor which is not that expensive about $34 plus shipping since they don't sell just the nylon gear. Hope this helps
Repair Help & Product Troubleshooting for Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover F7458-900 SteamVac The brushes quit

My Hoover F7458-900 was doing the same thing, brushes not turning and since it is about 7 years old and out of warrenty I decided I had nothing to lose so I took it apart after reading all the other posts on this problem. The brushes are actually tu ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Hoover f7458-900 brushes dont spin - Hoover F7458-900 Upright Vacuum

... Hoover F7458-900 Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou

Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover F7452-900 brushes quit working - Hoover F7452-900 SteamVac Upright Vacuum

... Hoover F7452-900 SteamVac Upright Vacuum

My quite new neumatic henry hoover is really difficult to push - you need all your strength. I do not have the brushes down and its still really hard to push - can anyone advise? thanks

... Henry Numatic "" Canister Vacuum

My scrub brushes quit working on modelf5915-900 in less than one year this is my second machine in 3 years. Now I'm very angry with hoover company. Can this be fixed and how much will it cost me? Steam cleaners

There are a couple of possibilities: the first and most simple fix would be to replace the brush-block, which simply releases from the bottom by pushing the retaining tabs free. If you pull this out and attempt to spin the brushes by spinning the gre ... Hoover Vacuums

My Hoover Windtunnel dual v brushes quit turning ....I took it Apart but I see no obvious problems. How can I fix it ?

... Hoover U8126-900 Wind Tunnel Dual V Bagless Upright Vacuum

Brush won't spin. - Hoover F7458-900 Upright Vacuum

... Hoover F7458-900 Upright Vacuum

Spin brushes will not spin - Hoover F7458-900 Upright Vacuum

... Hoover F7458-900 Upright Vacuum

The brushed roller on my Hoover Upright Canister has quit turning. Is this a broken belt? A friend recommended a "reset" button--is there such a thing?? Everything else works fine; power, suction, headlight. That belt just doesn't work anymore since we accidentally caugght the edge of a throw rug.

Belt. There is no reset on this model. ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

I have a Hoover linx cordless stick vac. I have not had it but several months and it has quit sucking anything up. It worked great when I first got it. I was so excited at how well it worked. It had gotten hair wrapped around the brushes but I got that out and thought it would work better. It is turning and sounds like it is working but it does not pick it up. I could use your help please. Keely

... Hoover Platinum LiNX Cordless Stick Vacuum

Hi, i have a hoover steam vac agilty. the brushes on the bottom front quit spinning. they are not locked up as i can freely turn them by fingers. is there a belt that i need to replace? if so, how do i get at it to replacec it? thank you for any assistance

The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum motor to spin a turbine and in turn spin the brushes. Most likely that path of air is clogged with hair or carpet fuzz. On the top of the machine there is a litt ... Hoover Vacuums

My FEIN 9-55-'13 recently started making more noise and is now officially a "screamer". There also developed quite a vibration associated with the noise which made me think it was probably bearings. So I took it apart and found no detectable play or lateral movement in the bearings, they seem fine to me. So I thought perhaps the brushes. The rotor where the brushes ride is quite black but I can't figure out how to get to those brushes, although I don't really think they are causing the noise

This problem is only caused by one thing the motor bearings are noisy, I have never found any other reason, they may look good and fell good but trust me replace the motor and the noise ... Fein 9-55-13 Turbo II Bagged Canister Vacuum

I have a Hoover F7458-900 steamVac all terain. I

You can reach under the brush (on top) and pull down. The manual for an all terrain is here to download\015\012\015\012F7452900 ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

I have a hoover all terrain cleaning for carpets and hard floors and the Brushes will not rotate. I have replaced the filter on the bottom which is recommended by hoover and the brushes still wont rotate. Please advise

I assume this unit has no mechanism to turn the brush but instead using the air flow to activate the brush, in this instance it could be that there is dirt which is caught up in the brush which is stopping the rotation.A nice good clean and make sure ... Hoover Vacuums

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?

Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.

Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Broken Brush on Hoover SteamVac Need to order new brushes

Yes you can order a brush block. It comes complete it is around $35. You can buy or order them at any vac shop or call me at my shop and I can ship them out.Josh 614.868.0799 m-f 9:30-6 sat 10-2 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move

There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Hoover steamvac Spinscrub F7222-900 brushes do not engage. Brushes will spin when unit is laid down and the brushes are pushed upward, forcing the male brush linkage into the female receptacle , but when the unit is stood up it disengages. Turning the switch on and off does not make a difference.

That's the way it's supposed to work. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0715 seconds