Having problems with your Hoover F7205900 SteamVac V2 Wet/Dry Vacuum ?

Where can I get the valve

\015 IThe valve popped out of the blue detergent container and caused the solution to run out. I tried to get a new rubber seal, but was informed that I only can buy the whole container for $79. I think that is robbery, since there is only the seal defect. Can someone point me in the right direction on where to buy just the seal or maybe the valve?\015\012Thanks for your help\015

Answers :

Try this site:  http://www.daltonvacuum.com/scripts/ProdList.asp?idCategory=258&nameCate=Hoover&nameSubCate=Steam%20Vac%20Parts
Repair Help & Product Troubleshooting for Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a lawn sprinkler system that has a main inlet valve that opens when the sprinkler is run. This inlet valve failed after a recent long freeze when water retained in the valve became ice and then expanded. Questions: 1. Can I replace just the plastic parts that broke or do I have to replace the total valve? The valve is made by FEBCO,CA and the following is written on the valve: 4010387; 765-PUB; B 6412 and 150 MWWP. 2. Where can I get the valve or the parts? My zip code is 77479 and I ca

Yes you can, take the piece into home depot they can help with it. usually you can replace the total valve as awhole , its easier to do it this way, and still cost effective :) \015\012\015\012press add a comment in upper right corner if ... Vacuums

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper

... Vacuums

My Hoover 97441-980 Dual Steam Vac won't hold detergent. The valve is bad. How can I get the old valve out so that I can replace it?

Just grab the valve stem with a pair of needle nose pliers and pull it out, then you can gently work out the outer valve with the pliers, and then remove the gasket. The older tanks tend to crack around the valve which may be the whole problem, but t ... Hoover Vacuums

The valve pipe assembly just popped off our Dyson DC 17. How do I get it back on? I see it appear the arm of the assembly needs to be captured but I can't figure how to get it all lined up without forcing it together.

... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Scunci steamcanister model 52038 Steam does not get from canister through hose to nozzle. No apparent leaks - hose does not get warm. appears may be valve problem from canister to hose. Only used bottled water - barely used this machine.

... Scunci Vacuums

Where can I get the valve

Try this site:  http://www.daltonvacuum.com/scripts/ProdList.asp?idCategory=258&nameCate=Hoover&nameSubCate=Steam%20Vac%20Parts ... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Gas valve on bottom leaks is there anywhere to get a new one.

\012Hi,\012That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy ... Vacuums

Electrolux epic 6500 turns off with new bag installed and hose removed. How do I get the control valve out to check it...?

... Electrolux LE, 2100, 6500 Canister Bag Lock Out Valve

How do you get the tank valves out of Hoover F7431-900? Does it take a special tool?

Pull down firmly on valves they will come out (soap or water side) then firmly push new valve in. By design valves are self sealing to plastic tank. ... Hoover F7431-900 SteamVac Vacuum

Help!!! I bought a replacement nozzle valve for a hoover steam vac hose and I can't get it back in right. Does anyone know where I can find an illustration of this assembly??

Hessco.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I can't get the plastic steam valve knob off. There is a hex set screw on the stem, inside the machine; I was able to remove that but the knob still won't budge off the stem. Any tips?

... Vacuums


No, there is only two possibilities. One, the low voltage wires are touching somewhere in the system or two, the relay is stuck in the on position. To find out which it is disconnect the low voltage wire from the unit (theres two clips on the side) a ... Beam Industries Wet/Dry Auto Central System Vacuum

Hello- My Europro EP965 is not shooting out the steam when I activate the switch on the handle. It does not work with the steam iron as well. The indicator lights work and it creating the steam, it is just not letting it out. I believe it is the valve inside, how do I get to it?

Fixya.com is a worthless website.\015\012Thank you ... Euro-Pro S3325 Handheld Steam Vacuum

I have a Hoover Steam Vac V2, model #F7430-900. The spring loaded valve on the soap dispenser needs replacing -is this possible or do I have to get the entire tank. Thanks

Hoover Steam Vac V2, Model #F7430-900\015\012I have a Hoover Steam Vac V2, model #F7430-900. The spring loaded valve on the soap dispenser needs replacing -is this possible or do I have to get the entire tank. ... Vacuums

I have a Hoover 6630-900 bagless upright. The "valve arm rear, part #38719048" broke. I have a repalcement part, but cannot get the spring, frontt and rear arms assembled correctly. Ant hints? Do you have a photo of the assembly on the vac? Thanks, Lee Duncan

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Why does my bissel proheat 2x model 8960 keeps stopping? the red valve door keeps getting shut

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e

The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I am trying to replace the lower hose valve assembly on my hoover windtunnel U5786. I have disassembled it to the point of loosening the old part, but can't get it to release.

... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I need a steam valve for model ep923h were can i get it

... Euro-Pro EP923 Canister Steam Vacuum

Polti Vaporetto I have a problem with my steam cleaner. Cannot get steam to come out, and the big valve at the top just keeps turning in both directions. So can't empty it. I have'nt got an instruction manual either as it was given to me. Any suggestions!!! Terena

Dear Terena \015\012\015\012Had the same problem with a polti vaporetto 1500 ( vtt 1500 ) after butchering the big valve on the top I realised that the problem was that there was a blockage in the black pipe that comes from the machine to ... Polti Vaporetto 2400 Canister Steam Vacuum

Cant get cover back on Bissel Pro Heat

... Bissell 8910 ProHeat Clear View Upright Vacuum

Hoover steamvac trigger valve is stuck open. water

... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

Soap solution valve on wand is not working.

No quick fix. Just make sure to run clean water through it before storing. Also, soak it in hot water, when it becomes plugged. I have dismantled my a few times, to clean it out, but have kept it clean to void future problems. ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

How do i get the steam in my unused polti vaporetto 2400. red to move up the flexihose to the head

... Polti Vaporetto 2400 Canister Steam Vacuum

Bissell 7920. Took it apart how do i align the solution valve

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0423 seconds