Having problems with your Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum ?

Brushes will not rotate - Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum


Answers :

I can't tell for sure from the pictures, but there are two possibilities - the drive belt to the brushes broke, or the brush can't turn due to excessive hair wrapped around the shaft. If the belt is OK but the brush does not turn, you should smell burning rubber.

If the belt is broken, you have to remove the bottom plate to expose the brush, remove the brush and the broken belt, and replace the belt, and put it back to gether. While you have the brush out, now would be a good time to clean it - remove the hair, etc from the brush and around the shaft. Good Luck!
Repair Help & Product Troubleshooting for Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes will not rotate - Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum


I can't tell for sure from the pictures, but there are two possibilities - the drive belt to the brushes broke, or the brush can't turn due to excessive hair wrapped around the shaft. If the belt is OK but the brush does not turn, you should smell b ... Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum

Brushes are not rotating - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this problem.First, what you'll need to do is take the brush block out of the machine. To do this there are 4 clips on the brush bloc ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Why did the brushes stop rotating? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


It could be a few different reasons, 1. The belt is broken, 2. The motor has died, 3. There is an obstruction, or some such thing stopping the bar from rotating (often hair and/or string) 4. The contact switch is defective. (switch that turns beater ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Why did the brushes stop rotating? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Please check two things: \015\012(1) The shutoff switch on the hood is NOT set to OFF for brush speed.\015\012(2) Remove the red filter panel from under the cleaner, behind the brushes, and clean the hair/debris from the screen filter. S ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brush does not rotate - Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum


... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Brushes don't rotate - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Hey are driven by a belt just replace it. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Rotating brushes don't rotate - Hoover F5872-900 SteamVac Wet/Dry Vacuum


Check belt, may be broken or may have come off the brush bar and replace. ... Hoover F5872-900 SteamVac Wet/Dry Vacuum

F7210-900 steam vac repair book - Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum


... Hoover F7210-900 SteamVac V2 Upright Wet/Dry Vacuum

How to remove a single brush from brush rack - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover F7412-900 brushes stopped working - Hoover F7222-900 SteamVac Upright Vacuum


... Hoover F7222-900 SteamVac Upright Vacuum

Hoover F7452-900 brushes quit working - Hoover F7452-900 SteamVac Upright Vacuum


... Hoover F7452-900 SteamVac Upright Vacuum

Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover f7452900 brushes wont turn? - Hoover F7452-900 SteamVac Upright Vacuum


Make sure that you have it on the carpet setting and not the hardwood/tile setting. also if you used the hose, make sure that the little door is closed. if all checked... remove the recovery tank, there should be a rubber grament on the stand pipe un ... Hoover F7452-900 SteamVac Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Brushes do not spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes will not spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


The belt maybe broke take a look to see if it is you maybe able to get replacement belt at walmart!!! :) amtnng ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes don't turn - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


I had the same problem and found a manual online. I never realized that there was a filter in the bottom of the machine. There are 2 red tabs, squeeze them together and pull ( I had to use a pair of pliers to pull). Note which is top and which is bot ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Agitator brushes wont turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Remove the brushes from the base of the unit by pulling down and unlatching at ends. Is there a drive pin present? The pin will be a 1/4 inch square pin, about two inches long. It engages to the drive mechanism.\015\012\015\012Second: ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My spin scrub brushes don't spin at all. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Check that the belt that spins the brushes is not broken, also that the\015\012gear that drives the belt is turning.\015\012\015\012Tom ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The rotary spin brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Belt either came off or broke ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes are not turning - Hoover F7220900 SteamVac V2 Upright Vacuum


There is a plastic shaft on the back of the block brush (spin \015\012scrubbers),\015\012 these wear out or break. You may need to replace the block brush. Or \015\012if the shaft is not broken it could also be the Turbine Gear. This is \015\012wh ... Hoover F7220900 SteamVac V2 Upright Vacuum

My brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


You probably have a break in the wiring somewhere or you got water in the motor. if there is a break replace all the wires and solder all the connections, if it still doesn't work start replacing switches and other components. if you got water in th ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes on the unit do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Try to clean the filter under the machine or the filter behind the clear plastic, were you see the hypnotic disc sprin that lets you know that the brushes are spinning. To remove : the plastic piece that looks like a triangle, ( were the indicator is ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes stopped spinning. what do i do? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


You simply just need to change your belt. This models uses Hoover belt # 40201160 and can be found at www.vacbelts.com. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1650 seconds