Having problems with your Hoover F7220900 SteamVac V2 Upright Vacuum ?

The brushes wont turn. every thing is cleaned and the switch is in the correct seting


Answers :

Check belt
Repair Help & Product Troubleshooting for Hoover F7220900 SteamVac V2 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes wont turn. every thing is cleaned and the switch is in the correct seting


Check belt ... Hoover F7220900 SteamVac V2 Upright Vacuum

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx


Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Every thing clean & sucking well except wont pickup off floor. brush in good condition &rotating. any answers would help.


This is hard to answer without see it in person. Check and make sure there is no broken pieces on the bottom where you could loose suction. Also make sure you have the machine set correctly for either bare floors or carpet. If it is on set on carpet ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???


... Vacuums

I noticed that the little side brush doesn't turn anymore and the Dirt Dog stops about every minute now so I have to keep turning it back on! I have dismantled the brushes and cleaned everything out but that didn't help at all. It doesn't really come apart any more than that for cleaning. Any suggestions as to where my problems may lie?


... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th


A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch


... Hoover Vacuums

When I turn my Dyson ball DC25 vacuum on and engage the brush it makes a screeching noise. I have cleaned the brush and the filters were cleaned a week ago and are in correctly.


Check if the belt still is connected and freely rotating the brush. Dyson vacuum belts are not replaceable.If the belt is going bad, the clutch assembly has to be replaced ... Dyson Vacuums

I have a roomba 435. I've had it for about 3 months, it had been working great until it started to sound a little different (louder). Now I noticed that it doesn't pick things up, it just pushes them around, I then discovered that the brushes aren't turning. I cleaned them out, no parts are missing. Brushes still won't turn. Help please.


Hmmmm....I know exactly what this is... Think back...the last time it was used when it worked...did it pick up something like a sock or get stuck somwhere?????? If you look on Ebay, it is polluted with this model Roomba. There is a gear that strips. ... iRobot Roomba 410 Robotic Vacuum

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem


... Oreck XL2200 Bagged Upright Vacuum

Agitator brushes wont turn even after cleaning


The brushes will not turn even wen the switch is turned on ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?


Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Brushes wont turn on shampooer


Dear Momneville\015\012I have the same steamcleaner and had the same problem, I took mine apart a found a clog between the turbine and the wheel that the turbine moves by vacuum when it gets glogged there is no vacuum to move the wheel. If you ... Hoover F7220900 SteamVac V2 Upright Vacuum

Today i was hoovering, and then my dyson just cut out! i left it a few hours then went back to it, it gave a little noise when i switched it on, then again i tried but it failed to come on! ive even changed the fuse in the plug! and now my dyson wont turn on at all, ive cleaned everything there is too clean! help! :D


It looks like you need a professional repair. If you're really lucky this may just be a break in the flex, or the switch has failed - both relatively cheap and simple to sort out. More likely, though, is a problem with the motor (carbon brushes worn ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob


Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

Spin brushes wont spin and the switch wont turn machine off. I have to unplug it. 


For the spin brushes it is most likely the motor is fried if you smell something burning it could be jammed or the wires have be shaken off the motor terminals. for it not turning off you need a new switch. ... Hoover F7431-900 SteamVac Vacuum

The rotating brush bar won't turn after i cleaned all the tangled hair and string off of t ,... I don't think i positioned the brush bar back in to the correct place that will connect ,,can you PLEASE help me?


Hello pmoongoddess. Here is a list of dyson vacuums with the parts diagrams for each one. Find your model and then open up that parts diagram showing the rotating brush component. It will show you exactly how it is positioned. I hope this helps. ... Dyson Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.


You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0949 seconds